The frame shown has pins at A, B and C; A and C are fixed to the ground 3 m apart, and B is 4 m above the ground and 1.8 m to the right of A. A vertical load of 12 kN acts on member AB at K, 0.9 m (horizontally) from A. Find the force FBC in member BC.
P = 12 kNL = 3 mH = 4 mhorizontal distance A to B = 1.8 mhorizontal distance A to K = 0.9 m
FBC = kN
8.Frames & machinesHard
A toggle press has two equal links AB and BC, each 80 mm long between pins. The joint B sits 10 mm above the line AC. Which downward force F at B produces a horizontal pressing force of 5000 N at the slider C? Neglect friction and weights.
Q = 5000 NAB = BC = 80 mmh = 10 mm
F = N
9.Shear force & bending momentMedium
The simply supported beam carries two point loads. Find the maximum bending moment Mmax in the beam.
L = 10 mP1 = 25 kN at 3 mP2 = 40 kN at 4 m
Mmax = kN·m
10.Shear force & bending momentHard
Find the bending moment Mx at the section x = 4 m from support A. Use sagging moments positive and upward shear on the left face positive.
L = 8 mP = 25 kN at 4 mw = 8 kN/m from 0 to 8 mx = 4 m
Mx = kN·m
11.Centroid & second moment of areaMedium
Find the second moment of area Ix of the T-section about the horizontal axis x through its centroid.
bf = 140 mmtf = 10 mmtw = 14 mmhw = 240 mm
Ix = × 10⁶ mm⁴
12.Centroid & second moment of areaHard
The T-section is used as a beam with the flange on top and carries a sagging bending moment of 10 kN·m. Find the size of the bending stress σtop at the top edge.
Dot product:a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.
Negative: the angle between the vectors is more than 90°.
2.Vectors: dot & cross product
Answer: (a × b)z = −14
Cross product:a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.
Cross product, component by component
(a × b)x = aybz − azby = (−4)·4 − 5·3 = −31
(a × b)y = azbx − axbz = 5·(−2) − (−2)·4 = −2
(a × b)z = axby − aybx = (−2)·3 − (−4)·(−2) = −14
Requested component
(a × b)z = −14
Answer
(a × b)z = −14
Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.
3.Beam support reactions
Answer: RA = 20.63 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·8 = 55·6 + 55·7
RB = 715/8 = 89.38 kN
ΣFy = 0: RA = 110 − 89.38 = 20.63 kN
Answer
RA = 20.63 kN
4.Beam support reactions
Answer: RB = 15 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 6·2 = 12 kN, acting at x̄ = 5 m
ΣMA = 0: RB·6 = 10·3 + 6·2·5
RB = 90/6 = 15 kN
ΣFy = 0: RA = 22 − 15 = 7 kN
Answer
RB = 15 kN
5.Truss: method of joints
Answer: FBC = −44.07 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·6 = 55·4 → Cy = 36.67 kN
ΣFy = 0: Ay = 55 − 36.67 = 18.33 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 3/3.606 = 0.8321, cos γ = 2/3.606 = 0.5547
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.
Two-force member BC
BC = √(1.2² + 4²) = 4.176 m
Whole frame: moments about A
The ground pushes on BC at C along CB; its horizontal component passes through A, only the vertical one has a moment.
FBC·(4/4.176)·3 = 12·0.9
FBC = 3.759 kN (compression)
Answer
FBC = 3.759 kN
8.Frames & machines
Answer: F = 1260 N
Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).
Link angle
sin θ = 10/80 = 0.125, θ = 7.181°
Link force
Flink = Q/cos θ = 5040 N
Force at B
F = 2·Flink·sin θ = 2·5000·tan θ = 1260 N
Answer
F = 1260 N
9.Shear force & bending moment
Answer: Mmax = 141 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
ΣMA = 0: RB·10 = 25·3 + 40·4
RB = 235/10 = 23.5 kN
ΣFy = 0: RA = 65 − 23.5 = 41.5 kN
Moment under each load
Keep the part left of each load.
under P1: M = RA·3 = 41.5·3 = 124.5 kN·m
under P2: M = RB·6 = 23.5·6 = 141 kN·m
Largest value
Mmax = 141 kN·m (under P2)
Answer
Mmax = 141 kN·m
10.Shear force & bending moment
Answer: Mx = 114 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 8·8 = 64 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 25·4 + 8·8·4
RB = 356/8 = 44.5 kN
ΣFy = 0: RA = 89 − 44.5 = 44.5 kN
Cut at x = 4 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 44.5·4 − 8·4·2 = 114 kN·m
Answer
Mx = 114 kN·m
11.Centroid & second moment of area
Answer: Ix = 31.58 × 10⁶ mm⁴
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 140·10 = 1400 mm², yf = 240 + 10/2 = 245 mm
Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.
Split into two rectangles
Measure every y from the bottom edge.
flange: Af = 300·10 = 3000 mm², yf = 260 + 10/2 = 265 mm