Statics: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Vectors: dot & cross product

Magnitude
|a| = √(ax² + ay² + az²)
Unit vector
û = a/|a|
Components from an angle
Fx = F·cos θ, Fy = F·sin θ
Dot product
a·b = axbx + ayby + azbz = |a||b|cos θ
Scalar projection of a onto b
a·b/|b|
Work
W = F·d
Cross product
a × b = (aybz − azby, azbx − axbz, axby − aybx)
Areas
parallelogram |a × b|, triangle ½|a × b|
Moment about O
MO = r × F, r = A − O
Volume of a parallelepiped
V = |a·(b × c)|

Method

  1. Write every vector in components; for a force given by a magnitude and an angle, use F·cos θ and F·sin θ.
  2. For lengths and directions use the magnitude √(x² + y² + z²) and the unit vector a/|a|.
  3. Use the dot product for angles, projections, perpendicularity and work: a·b = |a||b|cos θ.
  4. Use the cross product for perpendicular vectors, areas and moments: write the three components carefully, keeping the order a × b.

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Frames & machines

Equilibrium of each member
ΣFx = 0, ΣFy = 0, ΣM = 0
Two-force member
force along the line through its two pins
Pin force
equal and opposite on the two members it joins
Magnitude of a pin force
F = √(Fx² + Fy²)
Lever, pliers, bell crank
Fin·a = Fout·b
Toggle
Flink = F/(2 sin θ), Q = F/(2 tan θ)
Uniform load
resultant w·L at the middle of the load

Method

  1. Draw the whole structure and find the support reactions if there are no more than three unknowns.
  2. Spot the two-force members: loaded only at two pins, their force acts along the line between the pins.
  3. Take the frame apart and draw every member on its own, with equal and opposite pin forces where members meet.
  4. For each member, take moments about a pin with unknown forces, then use ΣFx = 0 and ΣFy = 0; combine components into a magnitude at the end.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Centroid & second moment of area

Centroid
ȳ = ΣAiyi/ΣAi
Rectangle
I = bh³/12
Parallel-axis theorem
I = Ic + A·d²
Composite section
I = Σ(Ic,i + Aidi²)

2Practice problems

1.Vectors: dot & cross productMedium
xyzab

Find the value of k for which the vectors a = (−4, −6, 3) and b = (6, 1, k) are perpendicular.

a = (−4, −6, 3)b = (6, 1, k)
k =
2.Vectors: dot & cross productHard
xyzab

For a = (2, 6, −1) and b = (0, 3, 2), find the z-component (a × b)z of the cross product a × b.

a = (2, 6, −1)b = (0, 3, 2)
(a × b)z =
3.Beam support reactionsMedium
w = 4 kN/mP = 25 kNABRA​ = ?6 m2 m

The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w along its whole length and a point load P at 6 m from the wall. Find the vertical reaction RA at the wall.

L = 8 mP = 25 kN at 6 mw = 4 kN/m from 0 to 8 m
RA = kN
4.Beam support reactionsHard
w = 2 kN/mP = 60 kNABRA​RB​ = ?3 m1 m3 m3 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 10 mP = 60 kN at 4 mw = 2 kN/m from 3 to 7 m
RB = kN
5.Truss: method of jointsMedium
ABCDEFGH25 kN15 kN4 × 4 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

F: 25 kN ↓G: 15 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member BG
  13. 13member DG
6.Truss: method of jointsHard
ABCDEFGH40 kN35 kN35 kN4 × 4 m3 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

D: 40 kN ↓F: 35 kN →G: 35 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
7.Frames & machinesMedium
OAB250 NQ240 mm60 mmFO​ = ?

The bell crank shown turns about the pin O. A vertical force of 250 N at A (240 mm from O) is balanced by a horizontal force at B (60 mm above O). Find the magnitude of the pin reaction FO.

F = 250 NOA = 240 mmOB = 60 mm
FO = N
8.Frames & machinesHard
w = 5 kN/m15 kN2 m2 m0.5 mABCD

The beam AB of the wall bracket shown is pinned at A and propped by the strut CD (C is 0.5 m below A). The beam carries a uniform load of 5 kN/m over its full length and a point load of 15 kN at its free end B. Find the force FCD in the strut.

w = 5 kN/mP = 15 kNAD = 2 mAB = 4 mAC = 0.5 m
FCD = kN
9.Shear force & bending momentMedium
P1​ = 70 kNP2​ = 45 kNABC5 m3 m1.5 m

The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.

L = 9.5 mP1 = 70 kN at 5 mP2 = 45 kN at 9.5 msupports at x = 0 and x = 8 m
Mx = kN·m
10.Shear force & bending momentHard
w = 5 kN/mP = 20 kNABsection6 m2 m

Find the bending moment Mx at the section x = 6 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mP = 20 kN at 6 mw = 5 kN/m from 0 to 8 mx = 6 m
Mx = kN·m
11.Centroid & second moment of areaMedium
190460246xdimensions in mm

A symmetric I-section has flanges 190 mm wide and 24 mm thick, an overall depth of 460 mm and a web 6 mm thick. Find its elastic section modulus Sx for bending about the horizontal centroidal axis x.

B = 190 mmH = 460 mmtf = 24 mmtw = 6 mm
Sx = × 10³ mm³
12.Centroid & second moment of areaHard
1602526012xhogging Mdimensions in mm

A cast-iron beam has the T-section shown, with the flange on top. The allowable stresses are 60 MPa in tension and 90 MPa in compression. Find the largest hogging bending moment Mallow the beam can carry (give its size).

bf = 160 mmtf = 25 mmtw = 12 mmhw = 260 mmσt,allow = 60 MPaσc,allow = 90 MPa
Mallow = kN·m

3Solutions

1.Vectors: dot & cross product

Answer: k = 10

Dot product: a·b = axbx + ayby + azbz = |a|·|b|·cos θ, a scalar. It gives the angle between two vectors, cos θ = a·b/(|a|·|b|), and it is zero when they are perpendicular. The scalar projection of a onto b is a·b/|b|, and a constant force F moving through a displacement d does work W = F·d.

Dot product equals zero

a·b = (−4)·6 + (−6)·1 + 3·k = 0
−30 + 3·k = 0

Solve for k

k = −(−30)/3 = 10

Answer

k = 10
2.Vectors: dot & cross product

Answer: (a × b)z = 6

Cross product: a × b = (aybz − azby, azbx − axbz, axby − aybx) is perpendicular to both vectors, and |a × b| = |a|·|b|·sin θ is the area of the parallelogram they span (the triangle has half of it). Order matters: b × a = −(a × b). The moment of a force F applied at point A about point O is MO = r × F, with r = A − O.

Cross product, component by component

(a × b)x = aybz − azby = 6·2 − (−1)·3 = 15
(a × b)y = azbx − axbz = (−1)·0 − 2·2 = −4
(a × b)z = axby − aybx = 2·3 − 6·0 = 6

Requested component

(a × b)z = 6

Answer

(a × b)z = 6

Check: a × b is perpendicular to both vectors, so its dot product with a and with b is zero.

3.Beam support reactions

Answer: RA = 57 kN

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the distributed load

W = 4·8 = 32 kN, x̄ = 4 m

Vertical equilibrium

RA = P + W = 25 + 32 = 57 kN

Answer

RA = 57 kN
4.Beam support reactions

Answer: RB = 28 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

w = 2 kN/mP = 60 kNABRA​RB​3 m1 m3 m3 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

UDL resultant: W = w·ℓ = 2·4 = 8 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 60·4 + 2·4·5
RB = 280/10 = 28 kN
ΣFy = 0: RA = 68 − 28 = 40 kN

Answer

RB = 28 kN
5.Truss: method of joints

Answer: member CG

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint C

BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.

ΣF⊥ = 0 → FCG = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 26.25 kN (T), BC: 27.5 kN (T), CD: 27.5 kN (T), DE: 13.75 kN (T), FG: 26.25 kN (C), GH: 13.75 kN (C), AF: 37.12 kN (C), HE: 19.45 kN (C), BF: 1.25 kN (T), CG: 0, DH: 13.75 kN (T), BG: 1.768 kN (C), DG: 19.45 kN (C)

Answer

Zero-force member: CG
6.Truss: method of joints

Answer: member BF

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint B

AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.

ΣF⊥ = 0 → FBF = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 62.92 kN (T), BC: 62.92 kN (T), CD: 72.08 kN (T), DE: 72.08 kN (T), FG: 90.83 kN (C), GH: 90.83 kN (C), AF: 34.9 kN (C), HE: 90.1 kN (C), BF: 0, CG: 35 kN (C), DH: 40 kN (T), FC: 34.9 kN (T), HC: 23.44 kN (T)

Answer

Zero-force member: BF
7.Frames & machines

Answer: FO = 1031 N

Machines: pliers, levers, linkages and clamps turn an input force into a larger or a differently directed output force. Draw one part as a free body and take moments about its pivot: the pin force drops out, and Fin·a = Fout·b gives the mechanical advantage a/b. The pin force then follows from ΣF = 0 on the same part. In a toggle, two links meet at a shallow angle θ; each link is a two-force member, so a small force F at the joint creates large link forces F/(2 sin θ) and a clamping force F/(2 tan θ).

Force at B

Q = 250·240/60 = 1000 N

Pin reaction

Ox = 1000 N, Oy = 250 N
FO = √(1000² + 250²) = 1031 N

Answer

FO = 1031 N
8.Frames & machines

Answer: FCD = 206.2 kN

Frames and machines: unlike a truss, a frame contains at least one member that carries forces at more than two points, or a load between its pins. First look for two-force members: a member loaded only at two pins has its force along the line through them, so it adds one unknown, not two. Then use the whole structure for the support reactions when there are no more than three unknowns. Finally take the frame apart: draw each member separately, with the pin forces equal and opposite on the two members they connect, and write ΣFx = 0, ΣFy = 0 and ΣM = 0 for it. Taking moments about a pin removes both components of that pin force from the equation.

Resultant of the uniform load

w·L = 5·4 = 20 kN at 2 m

Moments about A for the beam

FCD·0.2425·2 = 20·2 + 15·4 = 100 kN·m
FCD = 206.2 kN

Answer

FCD = 206.2 kN
9.Shear force & bending moment

Answer: Mx = 89.06 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam. The overhang load also acts about A.

ΣMA = 0: RB·8 = 70·5 + 45·9.5
RB = 777.5/8 = 97.19 kN
ΣFy = 0: RA = 115 − 97.19 = 17.81 kN

Cut under P1 and keep the left part

Mx = RA·5 = 17.81·5 = 89.06 kN·m

Answer

Mx = 89.06 kN·m
10.Shear force & bending moment

Answer: Mx = 60 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 5·8 = 40 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 20·6 + 5·8·4
RB = 280/8 = 35 kN
ΣFy = 0: RA = 60 − 35 = 25 kN
w = 5 kN/mP = 20 kNABRA​ = 25RB​ = 35section6 m2 m

Cut at x = 6 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 25·6 − 5·6·3 = 60 kN·m

Answer

Mx = 60 kN·m
11.Centroid & second moment of area

Answer: Sx = 2038 × 10³ mm³

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = Ic + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre.

Outer rectangle minus the two side cut-outs

Both cut-outs together are (B − tw) wide and hw = H − 2tf high, and share the axis x.

hw = 460 − 2·24 = 412 mm
Ix = (B·H³ − (B − tw)·hw³)/12 = (190·460³ − 184·412³)/12
Ix = 4.688 × 10⁸ mm⁴

Section modulus

c = H/2 = 230 mm
Sx = I/c = 4.688 × 10⁸/230
Sx = 2.038 × 10⁶ mm³ = 2038 × 10³ mm³

Answer

Sx = 2038 × 10³ mm³
12.Centroid & second moment of area

Answer: Mallow = 22.87 kN·m

Composite areas: split the section into rectangles. The centroid is the area-weighted average ȳ = ΣAᵢyᵢ/ΣAᵢ. The second moment of area about the centroidal axis adds each part’s own bh³/12 and its parallel-axis term A·d², where d is the distance from the part’s centroid to the overall centroid. Bending stress is σ = M·y/I.

Centroid

ȳ = (4000·272.5 + 3120·130)/7120 = 210.1 mm
top edge: c = 285 − 210.1 = 74.94 mm

Second moment of area

I = 160·25³/12 + 4000·62.44² + 12·260³/12 + 3120·80.06² = 5.338 × 10⁷ mm⁴

Moment allowed by each edge

Hogging: the top is in tension, the bottom in compression.

top edge: M = 60·5.338 × 10⁷/74.94 = 42.73 kN·m
bottom edge: M = 90·5.338 × 10⁷/210.1 = 22.87 kN·m

Governing value

Mallow = min = 22.87 kN·m (bottom edge)

Answer

Mallow = 22.87 kN·m

ExamProblems · examproblems.com/courses/statics