A cantilever carries a uniformly distributed load w over its whole length. Find the deflection δ at the free end.
w = 15 kN/mL = 1.5 mE = 11 GPa (timber)I = 160 × 10⁶ mm⁴
δ = mm
8.Beam deflectionHard
A simply supported beam carries a uniformly distributed load w. Its deflection may not exceed span/360. Find the smallest second moment of area Ireq that meets this limit.
w = 2 kN/mL = 3 mE = 200 GPa (steel)
Ireq = × 10⁶ mm⁴
9.Column bucklingMedium
A column of length L made of aluminium is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
L = 2.5 mE = 70 GPa (aluminium)b × h = 40 × 100 mm
Pcr = kN
10.Column bucklingHard
A solid round column of length L made of steel is pinned at both ends. It must carry 135 kN with a factor of safety of 3 against buckling. Find the smallest diameter d.
P = 135 kNn = 3L = 1.5 mE = 200 GPa (steel)
d = mm
3Solutions
1.Beam support reactions
Answer: RB = 76.67 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Moments about A
Counter-clockwise positive.
ΣMA = 0: RB·3 = 10·1 + 55·4
RB = 230/3 = 76.67 kN
Vertical equilibrium
RA = 10 + 55 − 76.67 = −11.67 kN
Answer
RB = 76.67 kN
RA is negative: the pin at A has to hold the beam down.
2.Beam support reactions
Answer: RB = 15.63 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 3·1 = 3 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·4 = 55·1 + 3·1·2.5
RB = 62.5/4 = 15.63 kN
ΣFy = 0: RA = 58 − 15.63 = 42.38 kN
Answer
RB = 15.63 kN
3.Shear force & bending moment
Answer: Vx = 10 kN
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 4·6 = 24 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 4·6·3
RB = 72/6 = 12 kN
ΣFy = 0: RA = 24 − 12 = 12 kN
Cut at x = 0.5 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
V = RA − (all downward loads left of the cut)
Vx = 12 − 4·0.5 = 10 kN
Answer
Vx = 10 kN
4.Shear force & bending moment
Answer: Mx = 66.67 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 10·6 = 60 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 20·2 + 10·6·3
RB = 220/6 = 36.67 kN
ΣFy = 0: RA = 80 − 36.67 = 43.33 kN
Cut at x = 2 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 43.33·2 − 10·2·1 = 66.67 kN·m
Answer
Mx = 66.67 kN·m
5.Truss: method of joints
Answer: member CG
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint C
BC and CD lie on one straight line and the joint carries no load. Balancing forces across that line leaves only CG.
ΣF⊥ = 0 → FCG = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Consistent units
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
w = 15 N/mm, L = 1500 mm
EI = 1.76 × 10¹² N·mm²
Deflection
δ = wL⁴/(8EI) = 15·1500⁴/(8·1.76 × 10¹²) = 5.393 mm
Answer
δ = 5.393 mm
8.Beam deflection
Answer: Ireq = 1.266 × 10⁶ mm⁴
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Deflection limit
δallow = L/360 = 3000/360 = 8.333 mm
Required second moment of area
I = 5wL⁴/(384·E·δallow) = 5·2·3000⁴/(384·200000·8.333) = 1.266 × 10⁶ mm⁴
Ireq = 1.266 × 10⁶ mm⁴
Answer
Ireq = 1.266 × 10⁶ mm⁴
9.Column buckling
Answer: Pcr = 120.3 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Smallest second moment of area
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Required critical load
Pcr = n·P = 3·135000 = 405000 N
KL = 1·1500 = 1500 mm
Solve for the diameter
d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·405000·1500²/(π³·200000))^(1/4) = 55.38 mm
Answer
d = 55.38 mm
Check: the slenderness KL/r is 108.3, so the column is slender and Euler applies.