Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.
The cantilever is fixed at A. It carries a uniformly distributed load w over its whole length and a point load P at 1.5 m from A. Find the bending moment MA at the fixed support A. Use sagging moments positive and upward shear on the left face positive.
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.
A simply supported beam carries a point load P at a = 2.5 m from support A. Find the deflection δP under the load.
A simply supported timber beam of rectangular section, 75 mm wide, carries a uniformly distributed load w over its whole span. Its midspan deflection may not exceed span/250. Find the smallest depth hreq of the section.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of aluminium is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
Answer: RA = 49.17 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Moments about A, counter-clockwise positive. Then vertical force balance.
Answer: RB = 22 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Moments about A, counter-clockwise positive. Then vertical force balance.
Answer: MA = −144 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Negative means hogging: tension on the top face.
Answer: B (x = 2 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Take moments about one support, then use the vertical force balance.
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
Answer: member BF
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
AB and BC lie on one straight line and the joint carries no load. Balancing forces across that line leaves only BF.
Solving all joints gives these member forces (T = tension, C = compression).
Answer: FAB = −12.37 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.
Answer: δP = 2.937 mm
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
Answer: hreq = 147.3 mm
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
In practice, choose the next standard depth above this value.
Answer: Pcr = 3.473 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 30.71 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
ExamProblems · examproblems.com/courses/structural-analysis