Structural Analysis: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Beam deflection

Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

2Practice problems

1.Beam support reactionsMedium
w0​ = 6 kN/mP = 15 kNABRB​ = ?5 m3 m

The simply supported beam (pin at A, roller at B) carries a linearly varying load that rises from zero at A to 6 kN/m at B. A point load P also acts at 5 m from A. Find the vertical support reaction RB.

L = 8 mw0 = 6 kN/mP = 15 kN at 5 m
RB = kN
2.Beam support reactionsHard
w0​ = 10 kN/mP = 15 kNABMA​ = ?3 m3 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is 10 kN/m at the wall and falls to zero at the free end B, plus a point load P at 3 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 6 mw0 = 10 kN/mP = 15 kN at 3 m
MA = kN·m
3.Shear force & bending momentMedium
P1​ = 15 kNP2​ = 25 kNABC1 m4 m1.5 m

The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.

L = 6.5 mP1 = 15 kN at 1 mP2 = 25 kN at 6.5 msupports at x = 0 and x = 5 m
Mx = kN·m
4.Shear force & bending momentHard
w = 10 kN/mP = 25 kNAB2 m4 m

The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.

L = 6 mP = 25 kN at 2 mw = 10 kN/m from 0 to 6 m
Mmax = kN·m
5.Truss: method of jointsMedium
ABBCACACB45 kN5 m4 m3 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 3 mB is 4 m from Avertical load = 45 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB40 kN5 kN6 m4 m2 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 6 mheight = 2 mB is 4 m from Avertical load = 40 kNhorizontal load = 5 kN ←
FAC = kN
7.Beam deflectionMedium
P = 16 kNABδ1 m2 m

A cantilever of length L is fixed at A and carries a point load P at a distance a = 1 m from A. Find the deflection δB at the free end B.

P = 16 kNa = 1 mL = 3 mE = 70 GPa (aluminium)I = 23 × 10⁶ mm⁴
δB = mm
8.Beam deflectionHard
w = 4 kN/mP = 29 kNδL = 8 m

A simply supported beam carries a uniformly distributed load w and a point load P at midspan. Using superposition, find the midspan deflection δmax.

P = 29 kNw = 4 kN/mL = 8 mE = 70 GPa (aluminium)I = 120 × 10⁶ mm⁴
δmax = mm
9.Column bucklingMedium
PL = 4 md = 25 mmcross-section

A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 4 mE = 200 GPa (steel)d = 25 mm
Pcr = kN
10.Column bucklingHard
P = 25 kNL = 3 md = ?cross-section

A solid round column of length L made of steel is fixed at both ends. It must carry 25 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.

P = 25 kNn = 2.5L = 3 mE = 200 GPa (steel)
d = mm

3Solutions

1.Beam support reactions

Answer: RB = 25.38 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.

Resultant of the triangular load

W = ½·6·8 = 24 kN
x̄ = 2L/3 = 5.333 m

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·8 = 24·5.333 + 15·5
RB = 25.38 kN
RA = 39 − 25.38 = 13.63 kN

Answer

RB = 25.38 kN
2.Beam support reactions

Answer: MA = 105 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·10·6 = 30 kN
x̄ = L/3 = 2 m

Moment about the wall

MA = W·x̄ + P·a = 30·2 + 15·3 = 105 kN·m

Answer

MA = 105 kN·m
3.Shear force & bending moment

Answer: Mx = 4.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam. The overhang load also acts about A.

ΣMA = 0: RB·5 = 15·1 + 25·6.5
RB = 177.5/5 = 35.5 kN
ΣFy = 0: RA = 40 − 35.5 = 4.5 kN

Cut under P1 and keep the left part

Mx = RA·1 = 4.5·1 = 4.5 kN·m

Answer

Mx = 4.5 kN·m
4.Shear force & bending moment

Answer: Mmax = 73.47 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 10·6 = 60 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 25·2 + 10·6·3
RB = 230/6 = 38.33 kN
ΣFy = 0: RA = 85 − 38.33 = 46.67 kN

Where is V = 0?

RA − P − w·x0 = 0 → x0 = (46.67 − 25)/10 = 2.167 m

Maximum moment

Mmax = RA·x0 − P·(x0 − 2) − w·x0²/2 = 73.47 kN·m

Answer

Mmax = 73.47 kN·m

It occurs at x = 2.167 m from A.

5.Truss: method of joints

Answer: FBC = −37.95 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB45 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 45·4 → Cy = 36 kN
ΣFy = 0: Ay = 45 − 36 = 9 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 3/3.162 = 0.9487, cos γ = 1/3.162 = 0.3162
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −36/0.9487 = −37.95 kN

Answer

FBC = −37.95 kN (compression)
6.Truss: method of joints

Answer: FAC = 25 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kN5 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 40·4 − 5·2 → Cy = 25 kN
ΣFy = 0: Ay = 40 − 25 = 15 kN
ΣFx = 0: Ax = 5 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.828 = 0.7071, cos γ = 2/2.828 = 0.7071
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −25/0.7071 = −35.36 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−35.36)·0.7071 = 25 kN

Answer

FAC = 25 kN (tension)
7.Beam deflection

Answer: δB = 13.25 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

P = 16000 N, a = 1000 mm, L = 3000 mm
EI = 1.61 × 10¹² N·mm²

Deflection at the free end

Deflection at the load plus the slope at the load times the remaining length.

δP = Pa³/(3EI) = 3.313 mm
θP = Pa²/(2EI) = 0.004969 rad
δB = δP + θP·(L − a) = Pa²(3L − a)/(6EI) = 13.25 mm

Answer

δB = 13.25 mm
8.Beam deflection

Answer: δmax = 62.22 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

P = 29000 N, w = 4 N/mm, L = 8000 mm, EI = 8.4 × 10¹² N·mm²

Each load on its own

δP = PL³/(48EI) = 29000·8000³/(48·8.4 × 10¹²) = 36.83 mm
δw = 5wL⁴/(384EI) = 5·4·8000⁴/(384·8.4 × 10¹²) = 25.4 mm

Add them

δmax = 36.83 + 25.4 = 62.22 mm

Answer

δmax = 62.22 mm
9.Column buckling

Answer: Pcr = 9.462 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Effective length

KL = 0.5·4000 = 2000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·19175/2000² = 9462 N = 9.462 kN

Answer

Pcr = 9.462 kN
10.Column buckling

Answer: d = 34.71 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2.5·25000 = 62500 N
KL = 0.5·3000 = 1500 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·62500·1500²/(π³·200000))^(1/4) = 34.71 mm

Answer

d = 34.71 mm

Check: the slenderness KL/r is 172.9, so the column is slender and Euler applies.

ExamProblems · examproblems.com/courses/structural-analysis