Structural Analysis: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Beam deflection

Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

2Practice problems

1.Beam support reactionsMedium
P1​ = 30 kNP2​ = 50 kNABRA​ = ?RB​1 m2.5 m2.5 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RA.

L = 6 mP1 = 30 kN at 1 mP2 = 50 kN at 3.5 m
RA = kN
2.Beam support reactionsHard
w0​ = 12 kN/mP = 55 kNABMA​ = ?6 m2 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is 12 kN/m at the wall and falls to zero at the free end B, plus a point load P at 6 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 8 mw0 = 12 kN/mP = 55 kN at 6 m
MA = kN·m
3.Shear force & bending momentMedium
P1​ = 25 kNP2​ = 60 kNABC1.5 m2.5 m1 m

The beam rests on a pin at A and a roller at B and overhangs B by 1 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment Mx under the load P1. Use sagging moments positive and upward shear on the left face positive.

L = 5 mP1 = 25 kN at 1.5 mP2 = 60 kN at 5 msupports at x = 0 and x = 4 m
Mx = kN·m
4.Shear force & bending momentHard
w = 6 kN/mP = 40 kNABsection5 m3 m

Find the bending moment Mx at the section x = 5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mP = 40 kN at 5 mw = 6 kN/m from 0 to 8 mx = 5 m
Mx = kN·m
5.Truss: method of jointsMedium
ABBCACACB30 kN6 m4 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 6 mheight = 2 mB is 4 m from Avertical load = 30 kN
FBC = kN
6.Truss: method of jointsHard
ABBCACACB10 kN10 kN4 m3 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 3 m from Avertical load = 10 kNhorizontal load = 10 kN ←
FBC = kN
7.Beam deflectionMedium
w = 15 kN/mδL = 1.5 m

A cantilever carries a uniformly distributed load w over its whole length. Find the deflection δ at the free end.

w = 15 kN/mL = 1.5 mE = 200 GPa (steel)I = 12 × 10⁶ mm⁴
δ = mm
8.Beam deflectionHard
w = 20 kN/mδL = 3 m

A simply supported beam carries a uniformly distributed load w. Its deflection may not exceed span/360. Find the smallest second moment of area Ireq that meets this limit.

w = 20 kN/mL = 3 mE = 200 GPa (steel)
Ireq = × 10⁶ mm⁴
9.Column bucklingMedium
PL = 1.5 md = 25 mmcross-section

A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 1.5 mE = 70 GPa (aluminium)d = 25 mm
Pcr = kN
10.Column bucklingHard
PL = 1.5 md = 60 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 1.5 mE = 200 GPa (steel)d = 60 mm
σcr = MPa

3Solutions

1.Beam support reactions

Answer: RA = 45.83 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 30 kNP2​ = 50 kNABRA​RB​1 m2.5 m2.5 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·6 = 30·1 + 50·3.5
RB = 205/6 = 34.17 kN
ΣFy = 0: RA = 80 − 34.17 = 45.83 kN

Answer

RA = 45.83 kN
2.Beam support reactions

Answer: MA = 458 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·12·8 = 48 kN
x̄ = L/3 = 2.667 m

Moment about the wall

MA = W·x̄ + P·a = 48·2.667 + 55·6 = 458 kN·m

Answer

MA = 458 kN·m
3.Shear force & bending moment

Answer: Mx = 0.9375 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam. The overhang load also acts about A.

ΣMA = 0: RB·4 = 25·1.5 + 60·5
RB = 337.5/4 = 84.38 kN
ΣFy = 0: RA = 85 − 84.38 = 0.625 kN

Cut under P1 and keep the left part

Mx = RA·1.5 = 0.625·1.5 = 0.9375 kN·m

Answer

Mx = 0.9375 kN·m
4.Shear force & bending moment

Answer: Mx = 120 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 6·8 = 48 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 40·5 + 6·8·4
RB = 392/8 = 49 kN
ΣFy = 0: RA = 88 − 49 = 39 kN
w = 6 kN/mP = 40 kNABRA​ = 39RB​ = 49section5 m3 m

Cut at x = 5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 39·5 − 6·5·2.5 = 120 kN·m

Answer

Mx = 120 kN·m
5.Truss: method of joints

Answer: FBC = −28.28 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB30 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·6 = 30·4 → Cy = 20 kN
ΣFy = 0: Ay = 30 − 20 = 10 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.828 = 0.7071, cos γ = 2/2.828 = 0.7071
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −20/0.7071 = −28.28 kN

Answer

FBC = −28.28 kN (compression)
6.Truss: method of joints

Answer: FBC = −2.795 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB10 kN10 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 10·3 − 10·2 → Cy = 2.5 kN
ΣFy = 0: Ay = 10 − 2.5 = 7.5 kN
ΣFx = 0: Ax = 10 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.236 = 0.8944, cos γ = 1/2.236 = 0.4472
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −2.5/0.8944 = −2.795 kN

Answer

FBC = −2.795 kN (compression)
7.Beam deflection

Answer: δ = 3.955 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

w = 15 N/mm, L = 1500 mm
EI = 2.4 × 10¹² N·mm²

Deflection

δ = wL⁴/(8EI) = 15·1500⁴/(8·2.4 × 10¹²) = 3.955 mm

Answer

δ = 3.955 mm
8.Beam deflection

Answer: Ireq = 12.66 × 10⁶ mm⁴

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Deflection limit

δallow = L/360 = 3000/360 = 8.333 mm

Required second moment of area

I = 5wL⁴/(384·E·δallow) = 5·20·3000⁴/(384·200000·8.333) = 1.266 × 10⁷ mm⁴
Ireq = 12.66 × 10⁶ mm⁴

Answer

Ireq = 12.66 × 10⁶ mm⁴
9.Column buckling

Answer: Pcr = 5.888 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Effective length

KL = 1·1500 = 1500 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·19175/1500² = 5888 N = 5.888 kN

Answer

Pcr = 5.888 kN
10.Column buckling

Answer: σcr = 49.35 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·60⁴/64 = 636173 mm⁴

Radius of gyration and slenderness

A = 2827 mm²
r = √(I/A) = √(636173/2827) = 15 mm
KL = 2·1500 = 3000 mm
KL/r = 3000/15 = 200

Critical stress

σcr = π²E/(KL/r)² = π²·200000/200² = 49.35 MPa

Answer

σcr = 49.35 MPa

ExamProblems · examproblems.com/courses/structural-analysis