A cantilever carries a uniformly distributed load w over its whole length and a point load P at its free end. Using superposition, find the deflection δ at the free end.
P = 19 kNw = 12 kN/mL = 2.5 mE = 200 GPa (steel)I = 160 × 10⁶ mm⁴
δ = mm
8.Beam deflectionHard
A propped cantilever is fixed at A and simply supported (propped) at B. It carries a point load P at midspan. EI is constant. Find the size of the bending moment MA at the fixed end.
L = 4 mP = 10 kN at 2 m
MA = kN·m
9.Column bucklingMedium
A column of length L made of steel is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
L = 4 mE = 200 GPa (steel)b × h = 20 × 40 mm
Pcr = kN
10.Column bucklingHard
A column of length L made of steel is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
L = 4 mE = 200 GPa (steel)d = 80 mm
σcr = MPa
3Solutions
1.Beam support reactions
Answer: RA = 35.5 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
ΣMA = 0: RB·5 = 35·2.5 + 45·3
RB = 222.5/5 = 44.5 kN
ΣFy = 0: RA = 80 − 44.5 = 35.5 kN
Answer
RA = 35.5 kN
2.Beam support reactions
Answer: RA = 29.6 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Free-body diagram
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Equilibrium
Moments about A, counter-clockwise positive. Then vertical force balance.
UDL resultant: W = w·ℓ = 6·4 = 24 kN, acting at x̄ = 3 m
ΣMA = 0: RB·5 = 25·1 + 6·4·3
RB = 97/5 = 19.4 kN
ΣFy = 0: RA = 49 − 19.4 = 29.6 kN
Answer
RA = 29.6 kN
3.Shear force & bending moment
Answer: Mx = 31.5 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 12·5 = 60 kN, acting at x̄ = 2.5 m
ΣMA = 0: RB·5 = 12·5·2.5
RB = 150/5 = 30 kN
ΣFy = 0: RA = 60 − 30 = 30 kN
Cut at x = 3.5 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 30·3.5 − 12·3.5·1.75 = 31.5 kN·m
Answer
Mx = 31.5 kN·m
4.Shear force & bending moment
Answer: Mx = 76.13 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 8·8 = 64 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 55·1 + 8·8·4
RB = 311/8 = 38.88 kN
ΣFy = 0: RA = 119 − 38.88 = 80.13 kN
Cut at x = 1 m and keep the left part
Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.
M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 80.13·1 − 8·1·0.5 = 76.13 kN·m
Answer
Mx = 76.13 kN·m
5.Truss: method of joints
Answer: FBC = −28.28 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·6 = 30·4 → Cy = 20 kN
ΣFy = 0: Ay = 30 − 20 = 10 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 2/2.828 = 0.7071, cos γ = 2/2.828 = 0.7071
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
Joint D
CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.
ΣF⊥ = 0 → FDH = 0
Check with the method of joints
Solving all joints gives these member forces (T = tension, C = compression).
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Consistent units
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
P = 19000 N, w = 12 N/mm, L = 2500 mm
EI = 3.2 × 10¹³ N·mm²
Each load on its own
δP = PL³/(3EI) = 19000·2500³/(3·3.2 × 10¹³) = 3.092 mm
δw = wL⁴/(8EI) = 12·2500⁴/(8·3.2 × 10¹³) = 1.831 mm
Add them
δ = 3.092 + 1.831 = 4.924 mm
Answer
δ = 4.924 mm
8.Beam deflection
Answer: MA = 7.5 kN·m
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). For a statically indeterminate beam, remove a redundant support and require the deflection there to be zero (compatibility).
Remove the prop
Without the prop the beam is a cantilever. Its free end would deflect under the load.
δload = P(L/2)²(3L − L/2)/(6EI) = 5PL³/(48EI)
Compatibility at the prop
The prop force RB alone lifts the free end by RBL³/(3EI). The prop holds B at zero deflection, so the two must cancel. EI cancels out.
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Smallest second moment of area
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.