In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
Beam support reactions
Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d
Method
Draw a free-body diagram and replace each support by its reactions.
Replace every distributed load by a single force at its centroid.
Take moments about one support to find the reaction at the other.
Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.
Shear force & bending moment
Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8
Method
Find the support reactions from equilibrium of the whole beam.
Cut the beam at the section you need and keep one side.
Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
For the maximum moment, find where the shear force is zero.
Truss: method of joints
Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression
Method
Find the support reactions for the whole truss.
Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
Assume tension; a negative answer means compression.
Beam deflection
Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2
Column buckling
Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)
2Practice problems
1.Beam support reactionsMedium
The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w along its whole length and a point load P at 3 m from the wall. Find the vertical reaction RA at the wall.
L = 8 mP = 45 kN at 3 mw = 6 kN/m from 0 to 8 m
RA = kN
2.Beam support reactionsHard
The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is zero at the wall and rises to 6 kN/m at the free end B, plus a point load P at 2 m from the wall. Find the magnitude of the reaction moment MA at the wall.
L = 5 mw0 = 6 kN/mP = 45 kN at 2 m
MA = kN·m
3.Shear force & bending momentMedium
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
20 kN @ 6 m10 kN/m, 0–12 m
1A (x = 0 m)
2B (x = 2 m)
3C (x = 4 m)
4D (x = 6 m)
5E (x = 8 m)
6F (x = 10 m)
7G (x = 12 m)
4.Shear force & bending momentHard
The simply supported beam carries a uniformly distributed load over part of its span. Find the maximum bending moment Mmax in the beam.
L = 5 mw = 6 kN/m from 1 to 3 m
Mmax = kN·m
5.Truss: method of jointsMedium
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 4 mheight = 4 mB is 1 m from Avertical load = 35 kN
FBC = kN
6.Truss: method of jointsHard
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
span = 6 mheight = 2 mB is 1 m from Avertical load = 10 kNhorizontal load = 20 kN ←
FBC = kN
7.Beam deflectionMedium
A cantilever carries a uniformly distributed load w over its whole length and a point load P at its free end. Using superposition, find the deflection δ at the free end.
P = 6 kNw = 20 kN/mL = 1.5 mE = 70 GPa (aluminium)I = 23 × 10⁶ mm⁴
δ = mm
8.Beam deflectionHard
A simply supported timber beam of rectangular section, 50 mm wide, carries a uniformly distributed load w over its whole span. Its midspan deflection may not exceed span/250. Find the smallest depth hreq of the section.
w = 1 kN/mL = 4 mE = 11 GPa (timber)b = 50 mm
hreq = mm
9.Column bucklingMedium
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
L = 5 mE = 70 GPa (aluminium)d = 50 mm
Pcr = kN
10.Column bucklingHard
A solid round column of length L made of steel is fixed at both ends. It must carry 125 kN with a factor of safety of 3 against buckling. Find the smallest diameter d.
P = 125 kNn = 3L = 2 mE = 200 GPa (steel)
d = mm
3Solutions
1.Beam support reactions
Answer: RA = 93 kN
Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.
Resultant of the distributed load
W = 6·8 = 48 kN, x̄ = 4 m
Vertical equilibrium
RA = P + W = 45 + 48 = 93 kN
Answer
RA = 93 kN
2.Beam support reactions
Answer: MA = 140 kN·m
Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.
Resultant of the triangular load
W = ½·6·5 = 15 kN
x̄ = 2L/3 = 3.333 m
Moment about the wall
MA = W·x̄ + P·a = 15·3.333 + 45·2 = 140 kN·m
Answer
MA = 140 kN·m
3.Shear force & bending moment
Answer: D (x = 6 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Support reactions
Take moments about one support, then use the vertical force balance.
R1 = 70 kN, R2 = 70 kN
Bending moment at every mark
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
MA = 0, MB = 120, MC = 200, MD = 240 kN·m, ME = 200, MF = 120, MG = 0
Answer
Mark D: MD = 240 kN·m
4.Shear force & bending moment
Answer: Mmax = 11.52 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Support reactions
Equilibrium of the whole beam.
UDL resultant: W = w·ℓ = 6·2 = 12 kN, acting at x̄ = 2 m
ΣMA = 0: RB·5 = 6·2·2
RB = 24/5 = 4.8 kN
ΣFy = 0: RA = 12 − 4.8 = 7.2 kN
Zero shear
The shear force starts at RA, stays constant over any unloaded part and falls with slope w inside the load.
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·4 = 35·1 → Cy = 8.75 kN
ΣFy = 0: Ay = 35 − 8.75 = 26.25 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Support reactions
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
ΣMA = 0: Cy·6 = 10·1 − 20·2 → Cy = −5 kN
ΣFy = 0: Ay = 10 − −5 = 15 kN
ΣFx = 0: Ax = 20 kN
Joint C
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
sin γ = 2/5.385 = 0.3714, cos γ = 5/5.385 = 0.9285
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Consistent units
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
P = 6000 N, w = 20 N/mm, L = 1500 mm
EI = 1.61 × 10¹² N·mm²
Each load on its own
δP = PL³/(3EI) = 6000·1500³/(3·1.61 × 10¹²) = 4.193 mm
δw = wL⁴/(8EI) = 20·1500⁴/(8·1.61 × 10¹²) = 7.861 mm
Add them
δ = 4.193 + 7.861 = 12.05 mm
Answer
δ = 12.05 mm
8.Beam deflection
Answer: hreq = 165.7 mm
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Consistent units
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
bh³/12 = Ireq → h = (12·1.894 × 10⁷/50)1/3 = 165.7 mm
Answer
hreq = 165.7 mm
In practice, choose the next standard depth above this value.
9.Column buckling
Answer: Pcr = 8.478 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Required critical load
Pcr = n·P = 3·125000 = 375000 N
KL = 0.5·2000 = 1000 mm
Solve for the diameter
d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·375000·1000²/(π³·200000))^(1/4) = 44.35 mm
Answer
d = 44.35 mm
Check: the slenderness KL/r is 90.18, so the column is slender and Euler applies.