Structural Analysis: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Beam deflection

Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

2Practice problems

1.Beam support reactionsMedium
w = 8 kN/mP = 45 kNABMA​ = ?4 m1.5 m0.5 m

The cantilever beam is fixed to the wall at A. It carries a uniformly distributed load w from the wall to 4 m and a point load P at 5.5 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 6 mP = 45 kN at 5.5 mw = 8 kN/m from 0 to 4 m
MA = kN·m
2.Beam support reactionsHard
w0​ = 12 kN/mP = 50 kNABMA​ = ?3 m5 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is zero at the wall and rises to 12 kN/m at the free end B, plus a point load P at 3 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 8 mw0 = 12 kN/mP = 50 kN at 3 m
MA = kN·m
3.Shear force & bending momentMedium
w = 4 kN/mABsection4.5 m3.5 m

Find the bending moment Mx at the section x = 4.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mw = 4 kN/m from 0 to 8 mx = 4.5 m
Mx = kN·m
4.Shear force & bending momentHard
w = 8 kN/mP = 60 kNAB3 m7 m

The simply supported beam carries a uniformly distributed load w over its whole span and a point load P. Find the maximum bending moment Mmax in the beam.

L = 10 mP = 60 kN at 3 mw = 8 kN/m from 0 to 10 m
Mmax = kN·m
5.Truss: method of jointsMedium
ABBCACACB40 kN5 m2 m4 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 5 mheight = 4 mB is 2 m from Avertical load = 40 kN
FBC = kN
6.Truss: method of jointsHard
ABCDEFGH20 kN35 kN20 kN30 kN4 × 4 m4 m

Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.

B: 20 kN ↓F: 35 kN →G: 20 kN ↓H: 30 kN ↓
  1. 1member AB
  2. 2member BC
  3. 3member CD
  4. 4member DE
  5. 5member FG
  6. 6member GH
  7. 7member AF
  8. 8member HE
  9. 9member BF
  10. 10member CG
  11. 11member DH
  12. 12member FC
  13. 13member HC
7.Beam deflectionMedium
w = 4 kN/mABθ4 m

A simply supported beam carries a uniformly distributed load w over its whole span. Find the slope θA of the beam at support A, in radians.

w = 4 kN/mL = 4 mE = 11 GPa (timber)I = 36 × 10⁶ mm⁴
θA = rad
8.Beam deflectionHard
w = 15 kN/mAB5 m

A propped cantilever is fixed at A and simply supported (propped) at B. It carries a uniformly distributed load w over its whole length. EI is constant. Find the reaction RB at the prop.

L = 5 mw = 15 kN/m
RB = kN
9.Column bucklingMedium
PL = 5 m20 × 100 mmcross-section

A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 5 mE = 200 GPa (steel)b × h = 20 × 100 mm
Pcr = kN
10.Column bucklingHard
P = 5 kNL = 6 md = ?cross-section

A solid round column of length L made of steel is fixed at the base and pinned at the top. It must carry 5 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.

P = 5 kNn = 2L = 6 mE = 200 GPa (steel)
d = mm

3Solutions

1.Beam support reactions

Answer: MA = 311.5 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the distributed load

W = 8·4 = 32 kN, x̄ = 2 m

Moment about the wall

MA = P·a + W·x̄ = 45·5.5 + 32·2 = 311.5 kN·m

Answer

MA = 311.5 kN·m
2.Beam support reactions

Answer: MA = 406 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·12·8 = 48 kN
x̄ = 2L/3 = 5.333 m

Moment about the wall

MA = W·x̄ + P·a = 48·5.333 + 50·3 = 406 kN·m

Answer

MA = 406 kN·m
3.Shear force & bending moment

Answer: Mx = 31.5 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 4·8 = 32 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 4·8·4
RB = 128/8 = 16 kN
ΣFy = 0: RA = 32 − 16 = 16 kN
w = 4 kN/mABRA​ = 16RB​ = 16section4.5 m3.5 m

Cut at x = 4.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 16·4.5 − 4·4.5·2.25 = 31.5 kN·m

Answer

Mx = 31.5 kN·m
4.Shear force & bending moment

Answer: Mmax = 210 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 8·10 = 80 kN, acting at x̄ = 5 m
ΣMA = 0: RB·10 = 60·3 + 8·10·5
RB = 580/10 = 58 kN
ΣFy = 0: RA = 140 − 58 = 82 kN

Where is V = 0?

V(3⁻) = RA − w·3 = 58 kN
V(3⁺) = 58 − 60 = −2 kN
The shear changes sign at the load, so the maximum is under the load.

Maximum moment

Mmax = RA·3 − w·3²/2 = 82·3 − 8·3²/2 = 210 kN·m

Answer

Mmax = 210 kN·m

It occurs at x = 3 m from A.

5.Truss: method of joints

Answer: FBC = −20 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB40 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·5 = 40·2 → Cy = 16 kN
ΣFy = 0: Ay = 40 − 16 = 24 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 4/5 = 0.8, cos γ = 3/5 = 0.6
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −16/0.8 = −20 kN

Answer

FBC = −20 kN (compression)
6.Truss: method of joints

Answer: member DH

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Joint D

CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.

ΣF⊥ = 0 → FDH = 0

Check with the method of joints

Solving all joints gives these member forces (T = tension, C = compression).

AB: 58.75 kN (T), BC: 58.75 kN (T), CD: 46.25 kN (T), DE: 46.25 kN (T), FG: 62.5 kN (C), GH: 62.5 kN (C), AF: 33.59 kN (C), HE: 65.41 kN (C), BF: 20 kN (T), CG: 20 kN (C), DH: 0, FC: 5.303 kN (T), HC: 22.98 kN (T)

Answer

Zero-force member: DH
7.Beam deflection

Answer: θA = 0.02694 rad

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). The slope θ = dv/dx is the first integral of M/(EI); in consistent units it comes out in radians.

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

w = 4 N/mm, L = 4000 mm
EI = 3.96 × 10¹¹ N·mm²

End slope

θA = wL³/(24EI) = 4·4000³/(24·3.96 × 10¹¹) = 0.02694 rad

Answer

θA = 0.02694 rad

That is 1.543°.

8.Beam deflection

Answer: RB = 28.13 kN

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). For a statically indeterminate beam, remove a redundant support and require the deflection there to be zero (compatibility).

Remove the prop

Without the prop the beam is a cantilever. Its free end would deflect under the load.

δload = wL⁴/(8EI)

Compatibility at the prop

The prop force RB alone lifts the free end by RBL³/(3EI). The prop holds B at zero deflection, so the two must cancel. EI cancels out.

RB·L³/(3EI) = wL⁴/(8EI) → RB = 3wL/8 = 3·15·5/8 = 28.13 kN

Answer

RB = 28.13 kN
9.Column buckling

Answer: Pcr = 5.264 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 100·20³/12 = 66667 mm⁴

Effective length

KL = 1·5000 = 5000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·66667/5000² = 5264 N = 5.264 kN

Answer

Pcr = 5.264 kN
10.Column buckling

Answer: d = 36.73 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2·5000 = 10000 N
KL = 0.7·6000 = 4200 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·10000·4200²/(π³·200000))^(1/4) = 36.73 mm

Answer

d = 36.73 mm

Check: the slenderness KL/r is 457.4, so the column is slender and Euler applies.

ExamProblems · examproblems.com/courses/structural-analysis