Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.
The beam rests on a pin at A and a roller at B and overhangs B by 1 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the shear force Vx just to the left of support B. Use sagging moments positive and upward shear on the left face positive.
The beam rests on a pin at A and a roller at B and overhangs B by 2 m to the free end C. A uniformly distributed load w acts over the whole length A–C. Find the maximum sagging bending moment Mmax between the supports.
Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.
Exactly one member of this truss carries no force under these loads. Which is the zero-force member? Click it in the diagram.
A simply supported beam carries a uniformly distributed load w over its whole span. Find the slope θA of the beam at support A, in radians.
A simply supported beam carries a uniformly distributed load w. Its deflection may not exceed span/360. Find the smallest second moment of area Ireq that meets this limit.
A column of length L made of aluminium is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
Answer: RB = 25 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Moments about A, counter-clockwise positive. Then vertical force balance.
Answer: RB = 61.8 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Moments about A, counter-clockwise positive. Then vertical force balance.
Answer: Vx = −31 kN
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Equilibrium of the whole beam. The overhang load also acts about A.
Answer: Mmax = 11.03 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut. Maximum moment: since dM/dx = V, the bending moment has its peak where the shear force passes through zero, either at a point load or inside a distributed load.
Equilibrium of the whole beam, including the load on the overhang.
Answer: FAC = 15.31 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
Answer: member DH
Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.
CD and DE lie on one straight line and the joint carries no load. Balancing forces across that line leaves only DH.
Solving all joints gives these member forces (T = tension, C = compression).
Answer: θA = 0.02032 rad
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). The slope θ = dv/dx is the first integral of M/(EI); in consistent units it comes out in radians.
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
That is 1.164°.
Answer: Ireq = 1309 × 10⁶ mm⁴
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Answer: Pcr = 89.96 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 12.34 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
ExamProblems · examproblems.com/courses/structural-analysis