Structural Analysis: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Beam support reactions

Equilibrium
ΣFx = 0, ΣFy = 0, ΣM = 0
Uniform load
resultant w·L at the middle of the load
Moment
M = F·d

Method

  1. Draw a free-body diagram and replace each support by its reactions.
  2. Replace every distributed load by a single force at its centroid.
  3. Take moments about one support to find the reaction at the other.
  4. Use ΣFy = 0 to find the remaining reaction, and check with a second moment equation.

Shear force & bending moment

Shear and moment
V = ΣF on one side, M = ΣF·d on one side
Bending stress
σ = M·y/I
Rectangle
I = bh³/12
Section modulus
W = I/ymax
Simply supported, uniform load
Mmax = wL²/8

Method

  1. Find the support reactions from equilibrium of the whole beam.
  2. Cut the beam at the section you need and keep one side.
  3. Shear force: sum of the vertical forces on that side. Bending moment: sum of their moments about the cut.
  4. For the maximum moment, find where the shear force is zero.

Truss: method of joints

Method of joints
ΣFx = 0, ΣFy = 0 at each joint
Method of sections
ΣM = 0 about a cut point
Member force
positive = tension, negative = compression

Method

  1. Find the support reactions for the whole truss.
  2. Method of joints: start at a joint with at most two unknown member forces and use ΣFx = 0 and ΣFy = 0.
  3. Method of sections: cut through the member you need and take moments about a point where the other unknown members meet.
  4. Assume tension; a negative answer means compression.

Beam deflection

Point load at midspan
δ = PL³/(48EI)
Uniform load, simply supported
δ = 5wL⁴/(384EI)
Cantilever, end load
δ = PL³/(3EI)
Cantilever, uniform load
δ = wL⁴/(8EI)
Superposition
δ = δ1 + δ2

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

2Practice problems

1.Beam support reactionsMedium
P1​ = 30 kNP2​ = 60 kNABRA​RB​ = ?2.5 m1.5 m1 m

The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.

L = 5 mP1 = 30 kN at 2.5 mP2 = 60 kN at 4 m
RB = kN
2.Beam support reactionsHard
w0​ = 6 kN/mP = 70 kNABMA​ = ?10 m

The cantilever beam is fixed to the wall at A. It carries a linearly varying load that is 6 kN/m at the wall and falls to zero at the free end B, plus a point load P at 10 m from the wall. Find the magnitude of the reaction moment MA at the wall.

L = 10 mw0 = 6 kN/mP = 70 kN at 10 m
MA = kN·m
3.Shear force & bending momentMedium
w = 8 kN/mABsection4.5 m1.5 m

Find the shear force Vx at the section x = 4.5 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 6 mw = 8 kN/m from 0 to 6 mx = 4.5 m
Vx = kN
4.Shear force & bending momentHard
w = 5 kN/mP = 30 kNABsection2 m1 m5 m

Find the bending moment Mx at the section x = 3 m from support A. Use sagging moments positive and upward shear on the left face positive.

L = 8 mP = 30 kN at 2 mw = 5 kN/m from 0 to 8 mx = 3 m
Mx = kN·m
5.Truss: method of jointsMedium
ABBCACACB60 kN4 m3 m2 m

Use the method of joints to find the force FAC in member AC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 3 m from Avertical load = 60 kN
FAC = kN
6.Truss: method of jointsHard
ABBCACACB55 kN15 kN4 m3 m2 m

Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.

span = 4 mheight = 2 mB is 3 m from Avertical load = 55 kNhorizontal load = 15 kN →
FBC = kN
7.Beam deflectionMedium
P = 9 kNABδ1 m3 m

A simply supported beam carries a point load P at a = 1 m from support A. Find the deflection δP under the load.

P = 9 kNa = 1 mL = 4 mE = 70 GPa (aluminium)I = 8.5 × 10⁶ mm⁴
δP = mm
8.Beam deflectionHard
w = 8 kN/mP = 3 kNδL = 2.5 m

A simply supported beam carries a uniformly distributed load w and a point load P at midspan. Using superposition, find the midspan deflection δmax.

P = 3 kNw = 8 kN/mL = 2.5 mE = 11 GPa (timber)I = 120 × 10⁶ mm⁴
δmax = mm
9.Column bucklingMedium
PL = 4 md = 60 mmcross-section

A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 4 mE = 200 GPa (steel)d = 60 mm
Pcr = kN
10.Column bucklingHard
P = 110 kNL = 2.5 md = ?cross-section

A solid round column of length L made of aluminium is fixed at the base and free at the top. It must carry 110 kN with a factor of safety of 3 against buckling. Find the smallest diameter d.

P = 110 kNn = 3L = 2.5 mE = 70 GPa (aluminium)
d = mm

3Solutions

1.Beam support reactions

Answer: RB = 63 kN

Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

P1​ = 30 kNP2​ = 60 kNABRA​RB​2.5 m1.5 m1 m

Free-body diagram

Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.

Equilibrium

Moments about A, counter-clockwise positive. Then vertical force balance.

ΣMA = 0: RB·5 = 30·2.5 + 60·4
RB = 315/5 = 63 kN
ΣFy = 0: RA = 90 − 63 = 27 kN

Answer

RB = 63 kN
2.Beam support reactions

Answer: MA = 800 kN·m

Cantilever equilibrium: a fixed support can push up and also resist rotation, so it gives a vertical reaction RA and a reaction moment MA. ΣFy = 0 gives RA, and moments about the wall give MA = Σ(load × distance from the wall). A distributed load acts as its resultant at the centroid of the load diagram.

Resultant of the triangular load

W = ½·6·10 = 30 kN
x̄ = L/3 = 3.333 m

Moment about the wall

MA = W·x̄ + P·a = 30·3.333 + 70·10 = 800 kN·m

Answer

MA = 800 kN·m
3.Shear force & bending moment

Answer: Vx = −12 kN

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 8·6 = 48 kN, acting at x̄ = 3 m
ΣMA = 0: RB·6 = 8·6·3
RB = 144/6 = 24 kN
ΣFy = 0: RA = 48 − 24 = 24 kN
w = 8 kN/mABRA​ = 24RB​ = 24section4.5 m1.5 m

Cut at x = 4.5 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

V = RA − (all downward loads left of the cut)
Vx = 24 − 8·4.5 = −12 kN

Answer

Vx = −12 kN
4.Shear force & bending moment

Answer: Mx = 75 kN·m

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Support reactions

Equilibrium of the whole beam.

UDL resultant: W = w·ℓ = 5·8 = 40 kN, acting at x̄ = 4 m
ΣMA = 0: RB·8 = 30·2 + 5·8·4
RB = 220/8 = 27.5 kN
ΣFy = 0: RA = 70 − 27.5 = 42.5 kN
w = 5 kN/mP = 30 kNABRA​ = 42.5RB​ = 27.5section2 m1 m5 m

Cut at x = 3 m and keep the left part

Only forces left of the cut appear. A UDL portion acts as one force at the middle of that portion.

M = RA·x − (each load left of the cut × its distance to the cut)
Mx = 42.5·3 − 30·(3 − 2) − 5·3·1.5 = 75 kN·m

Answer

Mx = 75 kN·m
5.Truss: method of joints

Answer: FAC = 22.5 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB60 kNAy​Cy​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 60·3 → Cy = 45 kN
ΣFy = 0: Ay = 60 − 45 = 15 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.236 = 0.8944, cos γ = 1/2.236 = 0.4472
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −45/0.8944 = −50.31 kN
ΣFx = 0: −FAC − FBC·cos γ = 0 → FAC = −(−50.31)·0.4472 = 22.5 kN

Answer

FAC = 22.5 kN (tension)
6.Truss: method of joints

Answer: FBC = −54.5 kN

Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

ABBCACACB55 kN15 kNAy​Cy​Ax​

Support reactions

Equilibrium of the whole truss. Moments about A, counter-clockwise positive.

ΣMA = 0: Cy·4 = 55·3 + 15·2 → Cy = 48.75 kN
ΣFy = 0: Ay = 55 − 48.75 = 6.25 kN
ΣFx = 0: Ax = −15 kN

Joint C

The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.

sin γ = 2/2.236 = 0.8944, cos γ = 1/2.236 = 0.4472
ΣFy = 0: Cy + FBC·sin γ = 0 → FBC = −48.75/0.8944 = −54.5 kN

Answer

FBC = −54.5 kN (compression)
7.Beam deflection

Answer: δP = 11.34 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

P = 9000 N, a = 1000 mm, b = 3000 mm, L = 4000 mm
EI = 5.95 × 10¹¹ N·mm²

Deflection under the load

δP = Pa²b²/(3EIL) = 9000·1000²·3000²/(3·5.95 × 10¹¹·4000) = 11.34 mm

Answer

δP = 11.34 mm
8.Beam deflection

Answer: δmax = 3.822 mm

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Consistent units

Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.

P = 3000 N, w = 8 N/mm, L = 2500 mm, EI = 1.32 × 10¹² N·mm²

Each load on its own

δP = PL³/(48EI) = 3000·2500³/(48·1.32 × 10¹²) = 0.7398 mm
δw = 5wL⁴/(384EI) = 5·8·2500⁴/(384·1.32 × 10¹²) = 3.083 mm

Add them

δmax = 0.7398 + 3.083 = 3.822 mm

Answer

δmax = 3.822 mm
9.Column buckling

Answer: Pcr = 78.48 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·60⁴/64 = 636173 mm⁴

Effective length

KL = 1·4000 = 4000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·636173/4000² = 78485 N = 78.48 kN

Answer

Pcr = 78.48 kN
10.Column buckling

Answer: d = 124.9 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 3·110000 = 330000 N
KL = 2·2500 = 5000 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·330000·5000²/(π³·70000))^(1/4) = 124.9 mm

Answer

d = 124.9 mm

Check: the slenderness KL/r is 160.1, so the column is slender and Euler applies.

ExamProblems · examproblems.com/courses/structural-analysis