Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
The beam has a pin at A and a roller at B, 4.5 m from A, and overhangs B to the free end C. Find the vertical reaction RB, taking upward as positive.
The simply supported beam has a pin at A and a roller at B. Find the vertical support reaction RB.
The beam rests on a pin at A and a roller at B and overhangs B by 1.5 m to the free end C. It carries a point load P1 between the supports and a point load P2 at C. Find the bending moment MB at support B. Use sagging moments positive and upward shear on the left face positive.
The marks A to G split the beam into six equal parts. At which mark is the bending moment largest in size, sagging or hogging? Click it in the diagram.
Use the method of joints to find the force FAB in member AB. Give tension as positive and compression as negative.
Use the method of joints to find the force FBC in member BC. Give tension as positive and compression as negative.
A cantilever carries a uniformly distributed load w over its whole length. Find the deflection δ at the free end.
A simply supported beam carries a uniformly distributed load w and a point load P at midspan. Using superposition, find the midspan deflection δmax.
A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of aluminium is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
Answer: RB = 101.7 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Replace each distributed load by its resultant (its area) acting at the centroid of the load diagram, and take moments about a support to remove that support’s reaction from the equation.
Counter-clockwise positive.
Answer: RB = 33.33 kN
Static equilibrium: a body at rest has ΣFx = 0, ΣFy = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.
Replace the supports with reaction forces. A roller gives one vertical reaction; with only vertical loads the pin gives one vertical reaction too.
Moments about A, counter-clockwise positive. Then vertical force balance.
Answer: MB = −97.5 kN·m
Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.
Equilibrium of the whole beam. The overhang load also acts about A.
Only P2 acts on the overhang, with lever arm a. It bends the beam upward over the support (hogging).
Answer: B (x = 2 m)
Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.
Take moments about one support, then use the vertical force balance.
Sum the moments of all forces on one side of the cut. Sagging is positive, hogging negative.
Answer: FAB = −14.67 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
Assume every member is in tension (pulling away from the joint). Only AB has a vertical component at A.
Answer: FBC = −37.35 kN
Method of joints: every pin of a truss is in equilibrium, so ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.
Equilibrium of the whole truss. Moments about A, counter-clockwise positive.
The roller gives only a vertical reaction, so joint C has just two unknown member forces. Assume both in tension.
Answer: δ = 4.969 mm
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
Answer: δmax = 73.6 mm
Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).
Work in N and mm: P in N, w in N/mm (kN/m = N/mm), L in mm, E in N/mm² (GPa × 1000), I in mm⁴.
Answer: Pcr = 67.29 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 47.98 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
ExamProblems · examproblems.com/courses/structural-analysis