产科护理
方法
- 把产妇放在时间轴上定位:孕周、产程阶段或产后第几天,再判断此时什么是正常的。
- 找出处于危险中的对象:母亲、胎儿或新生儿,或者其中不止一个。
- 把发现与其原因联系起来:减速用 VEAL CHOP,出血用四个 T,产后用 BUBBLE-HE。
- 优先选择改善血流和氧合的措施(侧卧、停用缩宫素、宫底按摩),然后再升级处理。
公式表、每个专题的关键方法步骤和 6 道练习题,完整解答附在最后。
Why must the fetal heart rate be monitored before and after external cephalic version?
An ultrasound at 30 weeks shows polyhydramnios and no visible fetal stomach bubble. Which fetal condition should be considered?
一支肾上腺素预充式注射器标示为 1:10 000(0.1 mg/mL)。医嘱为心脏骤停时 1 mg 静脉注射(IV)。你应给多少体积 V?
你需要用 25%(w/v)储备液配制 1000 mL 0.5%(w/v)溶液。 你需要多少容量的储备液 V₁?
滴注以 35 gtt/min 的速度通过滴系数为 15 gtt/mL 的输液器。患者在 4 小时内接受多少毫升 V?
一袋液体在 50 mL 中含药 1000 mg,以 12 mL/h 的速度输注。患者每小时获得多少毫克 D?
答案: C · The procedure can cause cord compression or abruption
External cephalic version turns a breech fetus to cephalic. It can cause fetal bradycardia, cord problems, abruption and fetomaternal bleeding, so the fetus is monitored and anti-D given to Rh-negative women.
答案: B · Oesophageal atresia
If the fetus cannot swallow, as in oesophageal atresia, amniotic fluid builds up and the stomach is not seen. Renal agenesis causes the opposite, severe oligohydramnios.
答案: V = 10 mL
Solution strengths: a percentage strength is grams per 100 mL, so 1% = 1 g/100 mL = 10 mg/mL. A ratio strength 1:1000 means 1 g in 1000 mL = 1 mg/mL; 1:10 000 is 0.1 mg/mL. For a dilution the amount of drug stays the same: C₁·V₁ = C₂·V₂.
美国的标签现在标示 mg/mL(1 mg/mL = 1:1000;0.1 mg/mL = 1:10 000)。切勿静脉推注 1 mg/mL 的肾上腺素。
答案: V₁ = 20 mL
Solution strengths: a percentage strength is grams per 100 mL, so 1% = 1 g/100 mL = 10 mg/mL. A ratio strength 1:1000 means 1 g in 1000 mL = 1 mg/mL; 1:10 000 is 0.1 mg/mL. For a dilution the amount of drug stays the same: C₁·V₁ = C₂·V₂.
答案: V = 560 mL
Infusion rates: a pump is set in mL/h = volume/time in hours. A gravity drip is counted in drops per minute: gtt/min = volume (mL) × drop factor (gtt/mL)/time (min). The drop factor is printed on the tubing package: macrodrip sets deliver 10, 15 or 20 gtt/mL (blood sets often 10 gtt/mL in the US, 15 in the UK) and microdrip sets 60 gtt/mL. Always use the drop factor the question or package gives.
答案: D = 240 mg/h
输注速率:输液泵按 mL/h = 体积/时间(小时)设定。重力滴注按每分钟滴数计:gtt/min = 体积 (mL) × 滴系数 (gtt/mL)/时间 (min)。 滴系数印在输液器包装上:普通输液器为 10、15 或 20 gtt/mL(输血器在美国常为 10 gtt/mL,在英国为 15),微量输液器为 60 gtt/mL。务必使用题目或包装给出的滴系数。
ExamProblems · examproblems.com/courses/maternity-nursing