Circuit Analysis 2: AC circuits: cram pack

Formula sheets, the key method steps for every topic and 16 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Complex numbers

Rectangular form
z = a + jb, j² = −1, z̄ = a − jb
Modulus and argument
|z| = √(a² + b²), tan θ = b/a (check the quadrant)
Polar and exponential form
z = r∠θ = r(cos θ + j sin θ) = r·ejθ
Division
z₁/z₂ = z₁z̄₂/|z₂|²
Product and quotient
r₁∠θ₁ · r₂∠θ₂ = r₁r₂∠(θ₁ + θ₂), r₁∠θ₁ / r₂∠θ₂ = (r₁/r₂)∠(θ₁ − θ₂)
De Moivre
(r∠θ)ⁿ = rⁿ∠nθ
n-th roots
zk = R1/n∠((φ + 360°·k)/n), k = 0 … n − 1
Quadratic with p² < 4q
z = −p/2 ± j√(q − p²/4)

Method

  1. Decide which form suits the operation: rectangular a + jb for adding and subtracting, polar r∠θ for multiplying, dividing, powers and roots.
  2. Multiply out with j² = −1; divide by multiplying the top and bottom by the conjugate of the denominator.
  3. Convert with r = √(a² + b²) and θ from a sketch of the point (check the quadrant), and back with a = r cos θ, b = r sin θ.
  4. For powers use De Moivre, (r∠θ)ⁿ = rⁿ∠nθ; for zⁿ = R∠φ list all n roots R1/n∠((φ + 360°k)/n).

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

LC resonance, Q factor & bandwidth

Natural frequency
ω0 = 1/√(LC), f0 = 1/(2π√(LC))
Energy
W = ½CV0² = ½Cv² + ½Li²
Peak current
Imax = V0√(C/L)
Quality factor
Q = 2π·(energy stored)/(energy lost per cycle)
Series RLC
Q = (1/R)√(L/C), BW = R/(2πL)
Parallel RLC
Q = R√(C/L), BW = 1/(2πRC)
Bandwidth
BW = f2 − f1 = f0/Q, f0 = √(f1f2)
Half-power frequencies
f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q))
Tank with coil resistance r
RD = L/(C·r) = Q²·r
Decay of the amplitude
e−Rt/(2L)

Method

  1. Find the resonance frequency first: ω₀ = 1/√(LC) and f₀ = ω₀/(2π).
  2. Decide whether the circuit is series or parallel: series Q = (1/R)√(L/C), parallel Q = R√(C/L).
  3. Use BW = f₀/Q for the bandwidth, or the shortcuts R/(2πL) (series) and 1/(2πRC) (parallel).
  4. For energy questions, use that the total energy ½CV₀² stays constant in an ideal LC circuit and swings between C and L every quarter period.

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Thévenin & Norton

Thévenin voltage
Vth = Vopen circuit
Thévenin resistance
Rth: all sources off, seen from a–b
Norton current
IN = Vth/Rth
Load current
IL = Vth/(Rth + RL)
Maximum power transfer
RL = Rth, Pmax = Vth²/(4Rth)

Method

  1. Remove the load and mark the two terminals a and b.
  2. Find the open-circuit voltage between a and b: this is Vth.
  3. Switch off all independent sources and find the resistance seen from a–b: this is Rth.
  4. Put the load back on the equivalent circuit: Vth in series with Rth.
  5. For the Norton equivalent, convert: IN = Vth/Rth, with RN = Rth in parallel.

2Practice problems

1.Complex numbersMedium
ReIm11−1−122−2−2z₁z₂w

Given z₁ = 1.5∠40° and z₂ = 0.5∠−95°, find the argument θ of w = z₁/z₂ in degrees, between −180° and 180°.

z₁ = 1.5∠40°z₂ = 0.5∠−95°
θ = °
2.Complex numbersHard
ReIm11−1−122−2−2θz

Use De Moivre's theorem to find the imaginary part of z⁶ for z = −2 − j2.

z = −2 − j2n = 6
Im(z⁶) =
3.AC impedance & phasorsMedium
100 V1000 HzR = 60 ΩL = 150 mHC = 47 µF

A series RLC circuit is connected to a 100 V (rms), 1000 Hz supply. Find the phase angle φ of the impedance, in degrees (positive when the current lags the voltage).

V = 100 V (rms)f = 1000 HzR = 60 ΩL = 150 mHC = 47 µF
φ = °
4.AC impedance & phasorsHard
VfR = 50 ΩL = 100 mHC = 0.047 µF

A series RLC circuit has R = 50 Ω, L = 100 mH and C = 0.047 µF. Find its bandwidth B (the width of the band between the half-power frequencies), in Hz.

R = 50 ΩL = 100 mHC = 0.047 µF
B = Hz
5.AC power & power factorMedium
P = 32 kWQSφ

A single-phase motor takes 32 kW at a power factor of 0.6 lagging from a 230 V supply. Find the line current I.

P = 32 kWpf = 0.6V = 230 V
I = A
6.AC power & power factorHard
50 V50 HzRs​ = 10 ΩXs​ = j6 ΩZL​ = ?

A 50 V (rms), 50 Hz source has an internal impedance Zs = 10 + j6 Ω. The load impedance ZL can be chosen freely. Find the maximum real power Pmax that can be delivered to the load.

Vs = 50 V (rms)f = 50 HzZs = 10 + j6 Ω
Pmax = W
7.LC resonance, Q factor & bandwidthMedium
V10 kΩ4.7 mH2.2 µF

A parallel RLC circuit has R = 10 kΩ, L = 4.7 mH and C = 2.2 µF. Find its quality factor Q.

R = 10 kΩL = 4.7 mHC = 2.2 µF
Q =
8.LC resonance, Q factor & bandwidthHard
V22 Ω10 mH470 nF200 mA

A series RLC circuit (R = 22 Ω, L = 10 mH, C = 470 nF) is driven at resonance with a current amplitude of 200 mA. Find the energy Ecycle dissipated in R during one cycle, in µJ.

R = 22 ΩL = 10 mHC = 470 nFIm = 200 mA
Ecycle = µJ
9.Three-phase powerMedium
ABCVL​ = 415 VNZ = 9 + j12 Ωper phase

A balanced Y-connected load with an impedance of 9 + j12 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 415 V. Find the total real power P absorbed by the load in kW.

VL = 415 VZ = 9 + j12 Ω per phase
P = kW
10.Three-phase powerHard
P = 80 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 80 kW at a power factor of 0.7 lagging from a 480 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 80 kWpf1 = 0.7pf2 = 0.92VL = 480 Vf = 50 Hz
Cph = µF
11.RC & RL transientsMedium
+−Vs​12 Vt = 0R = 33 ΩL150 mHi(t)

The inductor carries no current before the switch closes at t = 0. Find the voltage vL across the inductor at t = 5 ms.

Vs = 12 VR = 33 ΩL = 150 mHt = 5 ms
vL = V
12.RC & RL transientsHard
+−Vs​12 VR1​ = 22 ΩR2​ = 5 Ωcloses at t = 0L150 mHi(t)

The switch across R2 has been open for a long time, so the inductor current is steady. At t = 0 the switch closes and shorts out R2. How long after t = 0 does the inductor current reach 0.485 A? Find t.

Vs = 12 VR1 = 22 ΩR2 = 5 ΩL = 150 mH
t = ms
13.Thévenin & NortonMedium
R1​ = 15 ΩR3​ = 4 Ω+−V1​12 VR2​10 ΩAab

Find the Thévenin voltage Vth seen from terminals a–b.

V1 = 12 VR1 = 15 ΩR2 = 10 ΩR3 = 4 Ω
Vth = V
14.Thévenin & NortonHard
R1​ = 5 ΩR3​ = 5 Ω+−V1​6 VR2​12 ΩAIs​2.5 ABRL​6 ΩIL​

A load RL = 6 Ω is connected across a–b. Use a Thévenin equivalent to find the power PL delivered to the load.

V1 = 6 VIs = 2.5 AR1 = 5 ΩR2 = 12 ΩR3 = 5 ΩRL = 6 Ω
PL = W
15.Bode plots & marginsMedium
vin​L = 1 mHC = 0.1 µFR = 50 Ωvout​

In the series RLC band-pass filter shown the output is taken across R = 50 Ω, with L = 1 mH and C = 0.1 µF. Find the −3 dB bandwidth BW in Hz.

R = 50 ΩL = 1 mHC = 0.1 µF
BW = Hz
16.Bode plots & marginsHard
|H| (dB)0.10.1111010100100−60−40−200204060ω (rad/s)φ (°)ω (rad/s)−270−180−900ω180​ = ?

A unity-feedback loop has the open-loop transfer function L(s) = 1210/(s(s + 9)(s + 10)). Find the phase crossover frequency ω180, where ∠L(jω) = −180°.

L(s) = 1210/(s(s + 9)(s + 10))
ω180 = rad/s

3Solutions

1.Complex numbers

Answer: θ = 135 °

Polar form: z = r∠θ = r(cos θ + j sin θ) = r·ejθ, with r = |z| and θ = arg z. Back to rectangular form: a = r cos θ, b = r sin θ. The argument needs the quadrant: θ = atan(b/a) only when a > 0; for a < 0 add or subtract 180°. In polar form multiplication is easy: multiply the moduli and add the arguments; for division divide the moduli and subtract the arguments.

Modulus and argument of w

|w| = 1.5 / 0.5 = 3
θ = 40° − (−95)° = 135°

Argument

θ = 135°

Answer

θ = 135°
2.Complex numbers

Answer: Im(z⁶) = −512

De Moivre and roots: (r∠θ)ⁿ = rⁿ∠nθ. The equation zⁿ = R∠φ has exactly n roots, all with modulus R1/n, at the arguments (φ + 360°·k)/n for k = 0, 1, …, n − 1: they lie evenly spaced on a circle, 360°/n apart. A quadratic z² + pz + q = 0 with p² < 4q has the complex roots z = −p/2 ± j√(q − p²/4); a polynomial with real coefficients always has its complex roots in conjugate pairs a ± jb.

Polar form

z = −2 − j2 = 2√2∠−135°

De Moivre

z⁶ = (2√2)⁶∠−810° = 512∠−90°

Rectangular form

z⁶ = 512·(cos −90° + j sin −90°) = −j512
Im(z⁶) = −512

Answer

Im(z⁶) = −512
3.AC impedance & phasors

Answer: φ = 86.34 °

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·1000 = 6283 rad/s
XL = ωL = 6283·0.15 = 942.5 Ω
XC = 1/(ωC) = 1/(6283·47·10⁻⁶) = 3.386 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(XL − XC).

|Z| = √(R² + (XL − XC)²) = √(60² + (939.1)²) = 941 Ω

Phase angle

φ = arctan((XL − XC)/R) = arctan(939.1/60) = 86.34°

Answer

φ = 86.34°
4.AC impedance & phasors

Answer: B = 79.58 Hz

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonant frequency

f0 = 1/(2π·√(0.1·0.047·10⁻⁶)) = 2322 Hz

Quality factor

Q compares the reactance at resonance with the resistance: Q = ω₀L/R.

Q = (1/R)·√(L/C) = (1/50)·√(0.1/(0.047·10⁻⁶)) = 29.17

Bandwidth

B = f0/Q = 2322/29.17 = 79.58 Hz

Answer

B = 79.58 Hz
5.AC power & power factor

Answer: I = 231.9 A

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Line current

Only the real part of the power does work, so divide by the power factor.

I = P/(V·cos φ) = 32000/(230·0.6) = 231.9 A

Answer

I = 231.9 A
6.AC power & power factor

Answer: Pmax = 62.5 W

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Conjugate match

The load reactance cancels the source reactance, and the load resistance equals the source resistance.

ZL = Zs* = 10 − j6 Ω

Maximum power

I = Vs/(2Rs) = 50/20 = 2.5 A
Pmax = I²·RL = Vs²/(4Rs) = 50²/(4·10) = 62.5 W

Answer

Pmax = 62.5 W
7.LC resonance, Q factor & bandwidth

Answer: Q = 216.4

Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).

Resonance frequency

ω₀ = 1/√(LC) = 9834 rad/s

Quality factor

Q = R/(ω₀L) = 10000/(9834·0.0047) = 216.4

Answer

Q = 216.4

The bandwidth is 1/(2πRC) = 7.234 Hz.

8.LC resonance, Q factor & bandwidth

Answer: Ecycle = 189.5 µJ

Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).

Stored energy

W = ½·0.01·0.2² = 0.0002 J

Quality factor

Q = (1/22)·√(0.01/4.7 × 10⁻⁷) = 6.63

Energy lost per cycle

Ecycle = 2π·W/Q = 2π·0.0002/6.63 = 0.0001895 J = 189.5 µJ
check: ½·0.2²·22/2322 = 0.0001895 J

Answer

Ecycle = 189.5 µJ
9.Three-phase power

Answer: P = 6.889 kW

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Phase voltage

Vph = 415/√3 = 239.6 V

Phase current

|Z| = √(9² + 12²) = 15 Ω
Iph = 239.6/15 = 15.97 A

Total real power

Only the resistive part of each impedance absorbs real power.

P = 3·Iph²·R = 3·15.97²·9 = 6.889 kW

Answer

P = 6.889 kW

Check: cos φ = R/|Z| = 0.6, and √3·VL·IL·cos φ gives the same power.

10.Three-phase power

Answer: Cph = 656.7 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 80·tan(acos 0.7) = 80·1.02 = 81.62 kvar
Q2 = 80·tan(acos 0.92) = 80·0.426 = 34.08 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 47.54 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 480/√3 = 277.1 V, ω = 2π·50 = 314.2 rad/s
Cph = (QC/3)/(ω·V²) = 15845/(314.2·277.1²) = 656.7 µF

Answer

Cph = 656.7 µF
11.RC & RL transients

Answer: vL = 3.994 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 150 mH / 33 Ω = 4.545 ms
i(∞) = Vs/R = 12/33 = 0.3636 A

Inductor voltage

At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.

vL(t) = Vs·e−t/τ = 12·e−5/4.545 = 3.994 V

Answer

vL = 3.994 V
12.RC & RL transients

Answer: t = 3.5 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

Before t = 0 both resistors are in the loop; afterwards the closed switch bypasses R₂.

i(0) = 12/(22 + 5) = 0.4444 A
i(∞) = 12/22 = 0.5455 A
τ = L/R = 150/22 = 6.818 ms
i(t) = 0.5455 + (0.4444 − 0.5455)·e−t/τ

Solve for the time

e−t/τ = (0.485 − 0.5455)/(0.4444 − 0.5455) = 0.5985
t = 6.818·ln(1.671) = 3.5 ms

Answer

t = 3.5 ms
13.Thévenin & Norton

Answer: Vth = 4.8 V

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 15 ΩR3​ = 4 ΩSHORTR2​10 ΩAabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 15·10/(15+10) = 6 Ω
Rth = (R1 ∥ R2) + R3 = 6 + 4 = 10 Ω
R1​ = 15 ΩR3​ = 4 Ω+−V1​12 VR2​10 ΩAab+−Vth​

Find Vth, the open-circuit voltage

With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.

Vth = V1·R2/(R1+R2) = 12·10/(15+10) = 4.8 V
14.Thévenin & Norton

Answer: PL = 18.57 W

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 5 ΩR3​ = 5 ΩSHORTR2​12 ΩAOPENBabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 5·12/(5+12) = 3.529 Ω
Rth = (R1 ∥ R2) + R3 = 3.529 + 5 = 8.529 Ω
R1​ = 5 ΩR3​ = 5 Ω+−V1​6 VR2​12 ΩAIs​2.5 ABab+−Vth​

Find Vth, the open-circuit voltage

With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.

VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 4.235 + 2.5·3.529 = 13.06 V
Vth = VB = VA + Is·R3 = 13.06 + 2.5·5 = 25.56 V
Rth​ = 8.529 Ω+−Vth​25.56 VRL​6 ΩIL​

Connect the load to the Thévenin equivalent

The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.

IL = Vth/(Rth + RL) = 25.56/(8.529 + 6) = 1.759 A
PL = IL²·RL = 1.759²·6 = 18.57 W
15.Bode plots & margins

Answer: BW = 7958 Hz

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Resonant frequency

ω₀ = 1/√(LC) = 1/√(0.001·1 × 10⁻⁷) = 100000 rad/s
f₀ = ω₀/(2π) = 15915 Hz

Bandwidth

BW = R/L = 50/0.001 = 50000 rad/s = 7958 Hz

Answer

BW = 7958 Hz
16.Bode plots & margins

Answer: ω180 = 9.487 rad/s

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Phase crossover

(ω/9)·(ω/10) = 1 → ω180 = √(9·10) = 9.487 rad/s

Answer

ω180 = 9.487 rad/s

ExamProblems · examproblems.com/courses/circuit-analysis-2