Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane starts from rest and accelerates uniformly at 3.75 m/s² along a runway. Find its speed v after 700 m.
A stone is dropped from rest into a well. The splash is heard 3.8 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
A 10 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A ball is launched at 40° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A car takes a flat curve of radius 140 m. The coefficient of static friction between tyres and road is 0.3. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 2 kg ball on a string 0.8 m long is swung in a vertical circle. At the lowest point it moves at 6.5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A 1800 kg car drives up a 4° slope at a constant 36 km/h. Air resistance and rolling resistance together amount to 800 N. Find the power P the wheels must deliver, in kW.
A 2 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.25) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 1000 kg car moving at 16 m/s runs into a stationary 2000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
A 0.6 kg ball hits a wall at 28 m/s and bounces straight back at 8 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
A flywheel with a moment of inertia of 2 kg·m² spins at 1800 rpm. A brake applies a constant friction torque of 115 N·m. How long t does it take to stop?
A hollow sphere starts from rest and rolls without slipping down a slope inclined at 25° to the horizontal. Use g = 9.81 m/s². Its radius is 0.1 m. Find its angular velocity ω after it has rolled 7 m along the slope.
A 4 kW motor running at 2900 rpm drives a pinion with 20 teeth, which meshes with a gear with 25 teeth. The gear pair has an efficiency of 96%. Find the torque T1 on the motor shaft.
A 1.5 kW motor at 1440 rpm drives gear A (12 teeth), which meshes with gear B (45 teeth). Gear C (36 teeth) on the same shaft as B drives gear D (45 teeth) on the output shaft. Each gear mesh has an efficiency of 96%. Find the output torque Tout.
A 2.9 kg mass on a spring with k = 280 N/m is pulled 6 cm in the positive direction and released from rest at t = 0. Find its displacement x from equilibrium at t = 1.15 s (with sign).
A 1.4 kg mass on a spring with k = 160 N/m is pulled 14 cm from equilibrium and released. Find the total energy E of the oscillation.
A 12 kg mass is supported by a spring with a stiffness of 80 kN/m and a viscous damper with a damping coefficient of 160 N·s/m. Find the damping ratio ζ.
A 20 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 25 kN/m and k₂ = 30 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: v = 72.46 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: d = 64.04 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Only the positive root is physical.
Answer: a = 4.427 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: a = 2.747 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: t = 1.835 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: t = 5.125 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 20.3 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 125.2 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: P = 20.32 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Answer: x = 15.97 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: ΔK = 85333 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The lost energy goes into deformation, heat and sound.
Answer: J = 21.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: t = 3.278 s
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: ω = 59.01 rad/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Rolling without slipping: ω = v/r, and friction does no work at the contact point.
Answer: T1 = 13.17 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: Tout = 42.97 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: x = 1.798 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 1.568 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.08165
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: keq = 55 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics