Formula sheets, the key method steps for every topic and 16 practice problems, with full solutions at the back.
Find the current IR2 through R2.
Find the current IR1 delivered by the source, which flows through R1.
Use nodal analysis to find the node voltage VA (measured from ground).
The voltage source Vₛ between A and B has its + terminal at A, so it makes VA − VB = Vₛ. Use nodal analysis with a supernode to find the current Ix through the voltage source, from A to B as shown by the arrow.
Find the Thévenin resistance Rth seen from terminals a–b.
Find the Thévenin voltage Vth seen from terminals a–b.
The inductor carries a steady current of 3 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. How long does it take for the current to fall to 1.5 A? Find t.
Just before the switch closes at t = 0, the capacitor holds 15 V with the polarity shown. Find the capacitor voltage vC at t = 15 ms.
A series RLC circuit with C = 0.22 µF must resonate at 2000 Hz. Find the inductance L needed.
A resistor R1 is connected in series with a parallel combination of R2 and a capacitor C, across a 100 V (rms), 200 Hz supply. Find the rms current I.
A single-phase motor takes 31 kW at a power factor of 0.8 lagging from a 240 V supply. Find the line current I.
A single-phase load takes 35 kW at a power factor of 0.75 lagging from a 400 V, 50 Hz supply. A capacitor connected in parallel raises the power factor to 0.9. Find the reactive power QC the capacitor must supply.
A balanced three-phase load draws a line current of 80 A from a supply with a line-to-line voltage of 480 V. The power factor is 0.9 lagging. Find the total real power P drawn by the load in kW.
A balanced three-phase load takes 120 kW at a power factor of 0.7 lagging from a 480 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.92 lagging. The real power stays the same. The capacitors are connected in Δ. Find the capacitance Cph of each capacitor in µF.
A single-phase 500 kVA, 4160/480 V transformer operates at its rated load. Treat it as ideal. Find the current ILV in the low-voltage winding.
A single-phase 75 kVA transformer has a core loss of 600 W. At rated load and a power factor of 0.9 lagging its efficiency is 98%. Find the full-load copper loss Pcu,fl in watts.
Answer: IR2 = 3.309 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.
Answer: IR1 = 0.2119 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
Answer: VA = 4.71 V
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
Ground is the bottom wire. Known node voltages come straight from the sources (V1 = 12 V). Unknowns: VA, VB.
Currents leaving A through the resistors equal the current pushed into A by sources.
Currents leaving B through the resistors equal the current pushed into B by sources.
Answer: Ix = −2.585 A
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
The voltage source between A and B carries an unknown current, so KCL cannot be written at A or B separately. Enclose A, B and the source in one supernode: the current entering it equals the current leaving it.
KCL at node A alone: the current arriving through R₁ leaves through R₂ and through the voltage source.
A negative result means the real current flows against the arrow.
Answer: Rth = 9.8 Ω
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
Answer: Vth = 48 V
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.
Answer: t = 1.04 ms
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Answer: vC = 16.37 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.
Answer: L = 28.78 mH
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC).
Answer: I = 0.9632 A
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Multiply top and bottom by the complex conjugate to split Zp into real and imaginary parts.
Answer: I = 161.5 A
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Only the real part of the power does work, so divide by the power factor.
Answer: QC = 13.92 kvar
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
The real power P does not change; only the reactive power drawn from the supply does.
Answer: P = 59.86 kW
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Answer: Cph = 273.6 µF
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.
In a Δ bank each capacitor is connected between two lines.
Answer: ILV = 1042 A
Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.
Both windings carry the same apparent power.
Answer: Pcu,fl = 777.6 W
Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.
ExamProblems · examproblems.com/courses/electrical-engineering-fundamentals