Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.
An NPN transistor with β = 100 has voltage-divider bias from VCC = 12 V: R₁ = 39 kΩ from VCC to the base and R₂ = 12 kΩ from the base to ground. The collector resistor is RC = 4.7 kΩ and the emitter resistor is RE = 1.2 kΩ. Take VBE = 0.7 V and use the Thévenin equivalent of the divider (do not neglect the base current). Find the collector–emitter voltage VCE.
An NPN transistor with β = 100 switches a 680 Ω load resistor connected between VCC = 5 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. For reliable switching, design for a base current 2 times the minimum needed for saturation. Find RB in kΩ.
The op-amp is ideal and runs from ±15 V supplies; its output saturates at ±12 V. The inverting amplifier is driven by a sine wave. Find the largest input amplitude Vin,max (peak value) for which the output does not clip.
The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the output voltage Vout.
The inductor carries no current before the switch closes at t = 0. Find the energy W stored in the inductor at t = 10 ms, in mJ.
The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage vC at t = 150 ms.
Find the current IR2 through R2.
Find the current IR1 delivered by the source, which flows through R1.
An ideal buck converter turns 24 V into 14.4 V at 25 kHz with L = 220 µH. Find the peak-to-peak inductor ripple current ΔIL.
An ideal inverting buck-boost converter turns 48 V into −72 V for a 4 Ω load at 50 kHz. Find the smallest inductance Lcrit for continuous conduction.
A galvanometer with a resistance of 50 Ω is connected between a and b of the bridge shown (Vs = 3 V). Find the galvanometer current Ig from a to b, in µA.
A load cell (a full bridge of strain gauges) has a rated output of 1 mV/V at its rated load of 500 kg. It is excited with 5 V. Find its output Vo under a load of 125 kg.
Simplify F = BC + AB′C′ + A′B′C + ABC to its minimal sum-of-products form. How many literals L does the simplified expression contain?
A positive-edge-triggered D flip-flop starts with Q = 0 and receives the inputs shown at 6 rising clock edges. How many times N does Q change state?
Answer: VCE = 2.371 V
BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.
KVL around the base loop; the emitter current is (β + 1)·IB.
Answer: RB = 18.42 kΩ
BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.
Answer: Vin,max = 2.553 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Answer: Vout = 0.3 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
V₋ = 0, so each input resistor has its full input voltage across it.
Answer: W = 161.2 mJ
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
Answer: vC = 12.81 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.
Answer: IR2 = 0.44 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.
Answer: IR1 = 1.193 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
Answer: ΔIL = 1.047 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
While S is on, the inductor sits between Vin and Vo.
Answer: Lcrit = 6.4 µH
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Set the average inductor current equal to half the ripple current and solve for L.
Answer: Ig = 1304 µA
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Answer: Vo = 1.25 mV
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Answer: L = 7
Boolean algebra: the rules that simplify expressions are X + X′ = 1 and X·X′ = 0, X + X = X, absorption X + X·Y = X, the combining rule X·Y + X·Y′ = X, X + X′Y = X + Y and the consensus theorem XY + X′Z + YZ = XY + X′Z. De Morgan's laws turn (X·Y)′ into X′ + Y′ and (X + Y)′ into X′·Y′. A Karnaugh map applies these rules graphically: every group of two neighbouring cells is one use of XY + XY′ = X.
Answer: N = 2
Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.
A D flip-flop copies D at each rising edge: Q⁺ = D.
ExamProblems · examproblems.com/courses/electronics-1