Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 0.75 kW motor running at 1500 rpm drives a pinion with 18 teeth, which meshes with a gear with 60 teeth. The gear pair has an efficiency of 95%. Find the output torque T2 on the gear shaft.
An open belt connects a 120 mm pulley and a 200 mm pulley whose centres are 1000 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A solid steel shaft 1.5 m long carries a torque of 400 N·m. The angle of twist between its ends must not exceed 1°. Find the smallest diameter d that meets this limit.
A solid shaft must transmit 10 kW at 3000 rpm without the shear stress exceeding 40 MPa. Find the smallest diameter d that works.
A point in a thin plate is in plane stress: σₓ = −80 MPa, σᵧ = −70 MPa and τₓᵧ = −30 MPa, with σz = 0. Find the absolute maximum shear stress τabs at the point (considering all planes in three dimensions).
A point in a loaded part has σₓ = 140 MPa, σᵧ = 30 MPa and τₓᵧ = 50 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 30° clockwise from the x-axis.
A steel rod (diameter 40 mm, E = 200 GPa) sits inside a tube made of copper (outer diameter 80 mm, inner diameter 50 mm, E = 120 GPa). Both are 400 mm long and are compressed together between rigid plates by 300 kN. Find the shortening δ.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of steel is fixed at both ends. It must carry 65 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.
A 50 kg mass is supported by a spring with a stiffness of 50 kN/m and a viscous damper with a damping coefficient of 790 N·s/m. Find the damping ratio ζ.
A 20 kg mass hangs from spring k₃ = 100 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 60 kN/m and k₂ = 12 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: T2 = 15.12 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: θ = 175.4 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: d = 45.74 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: d = 15.94 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: τabs = 52.71 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. In three dimensions the absolute maximum shear stress is (σmax − σmin)/2 over all three principal stresses; in plane stress the third one is zero.
Here the out-of-plane circle governs: the absolute maximum is larger than the in-plane maximum R.
Answer: σθ = 69.2 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.1939 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: δ = 2.77 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 24.22 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: d = 38.05 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 131.4, so the column is slender and Euler applies.
Answer: ζ = 0.2498
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 7.281 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/machine-design