Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 100 mmd2​ = 200 mm720 rpmT1​ = 600 NT2​ = 300 NP = ?

A belt runs on a 100 mm driving pulley at 720 rpm. The tension is 600 N on the tight side and 300 N on the slack side. Find the power P transmitted, in kW.

d1 = 100 mmn1 = 720 rpmT1 = 600 NT2 = 300 N
P = kW
2.Gears & gear trainsHard
Ns​ = 16nr​ = ?Np​ = 15carrier fixed

In a planetary gear set the sun gear has 16 teeth and each planet gear has 15 teeth. The planet carrier is held fixed and the sun is driven at 3000 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 16Np = 15ns = 3000 rpm
nr = rpm
3.Torsion of shaftsMedium
d = ?T = 250 N·mL = 0.8 m

A solid aluminium shaft 0.8 m long carries a torque of 250 N·m. The angle of twist between its ends must not exceed 2°. Find the smallest diameter d that meets this limit.

T = 250 N·mL = 0.8 mG = 26 GPaφallow = 2°
d = mm
4.Torsion of shaftsHard
d = ?5 kW, 1500 rpm

A solid brass shaft transmits 5 kW at 1500 rpm. The shear stress must not exceed 60 MPa and the twist must not exceed 0.25° per m of length. Find the smallest diameter d that satisfies both limits.

P = 5 kWN = 1500 rpmτallow = 60 MPaθallow = 0.25°/mG = 39 GPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = −30σy​ = −50τxy​ = 30MPa

A point in a thin plate is in plane stress: σₓ = −30 MPa, σᵧ = −50 MPa and τₓᵧ = 30 MPa, with σz = 0. Find the absolute maximum shear stress τabs at the point (considering all planes in three dimensions).

σx = −30 MPaσy = −50 MPaτxy = 30 MPaσz = 0
τabs = MPa
6.Mohr’s circle & stress transformationHard
σx​ = −70σy​ = 60τxy​ = −10MPa

A point in a loaded part has σₓ = −70 MPa, σᵧ = 60 MPa and τₓᵧ = −10 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 45° clockwise from the x-axis.

σx = −70 MPaσy = 60 MPaτxy = −10 MPaθ = -45°
σθ = MPa
7.Axial stress & strainMedium
Ø 20 mmCopper2 mP = 45 kN

Find the elongation δ of the copper bar under the axial load.

P = 45 kNd = 20 mmL = 2 mE = 117 GPa
δ = mm
8.Axial stress & strainHard
100 kN12400 mm400 mmØ20Ø50σ2​ = ?

A steel segment (diameter 20 mm, length 400 mm, E = 200 GPa) and a segment made of brass (diameter 50 mm, length 400 mm, E = 100 GPa) are joined end to end and fixed between two rigid walls. An axial load of 100 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø20 mm, 400 mm, E = 200 GPasegment 2: brass, Ø50 mm, 400 mm, E = 100 GPaP = 100 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2 m20 × 40 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 2 mE = 200 GPa (steel)b × h = 20 × 40 mm
Pcr = kN
10.Column bucklingHard
PL = 2.5 md = 60 mmcross-section

A column of length L made of aluminium is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 2.5 mE = 70 GPa (aluminium)d = 60 mm
σcr = MPa
11.Mechanical vibrationsMedium
k = 150 kN/mζ = 0.45m = 15 kg

A 15 kg mass on a spring with a stiffness of 150 kN/m has a viscous damper giving a damping ratio of 0.45. Find the damped natural frequency fd of its free vibration in Hz.

m = 15 kgk = 150 kN/mζ = 0.45
fd = Hz
12.Mechanical vibrationsHard
k1​ = 50k2​ = 30m = 40 kg

A 40 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 50 kN/m and the lower one k₂ = 30 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 40 kgk1 = 50 kN/mk2 = 30 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 1.131 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 3.77 m/s

Power

P = (600 − 300)·3.77 = 1131 W = 1.131 kW

Answer

P = 1.131 kW
2.Gears & gear trains

Answer: nr = 1043 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 16 + 2·15 = 46

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −3000·16/46 = −1043 rpm
|nr| = 1043 rpm

Answer

nr = 1043 rpm

The ring turns opposite to the sun.

3.Torsion of shafts

Answer: d = 38.71 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Required polar moment

T = 250 N·m = 250000 N·mm
L = 0.8 m = 800 mm
G = 26 GPa = 26000 MPa
φ = 2·π/180 = 0.03491 rad
J = TL/(Gφ) = 250000·800/(26000·0.03491) = 220368 mm⁴

Diameter

d = (32J/π)1/4 = 38.71 mm

Answer

d = 38.71 mm

In practice you would round up to the next standard size.

4.Torsion of shafts

Answer: d = 37.15 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·1500/60 = 157.1 rad/s
T = P/ω = 5000/157.1 = 31.83 N·m

Diameter for strength

T = 31.83 N·m = 31831 N·mm
dτ = ∛(16·31831/(π·60)) = 13.93 mm

Diameter for stiffness

θ = 0.25·π/180/1000 = 4.363 × 10⁻⁶ rad/mm
G = 39 GPa = 39000 MPa
dφ = (32·31831/(π·39000·4.363 × 10⁻⁶))1/4 = 37.15 mm

Governing diameter

Both limits must hold, so the larger diameter governs.

d = max(13.93, 37.15) = 37.15 mm

Answer

d = 37.15 mm

Here stiffness governs.

5.Mohr’s circle & stress transformation

Answer: τabs = 35.81 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. In three dimensions the absolute maximum shear stress is (σmax − σmin)/2 over all three principal stresses; in plane stress the third one is zero.

στxyCσ1​σ2​

In-plane principal stresses

C = −40 MPa, R = √(10² + 30²) = 31.62 MPa
σ1 = −8.377 MPa, σ2 = −71.62 MPa, σz = 0

Largest of the three circles

τ = max(|σ1 − σ2|, |σ1|, |σ2|)/2 = max(63.25, 8.377, 71.62)/2 = 35.81 MPa

Answer

τabs = 35.81 MPa

Here the out-of-plane circle governs: the absolute maximum is larger than the in-plane maximum R.

6.Mohr’s circle & stress transformation

Answer: σθ = 5 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

σθ = −5 + −65·0 + −10·−1 = 5 MPa

Answer

σθ = 5 MPa
7.Axial stress & strain

Answer: δ = 2.449 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·20²/4 = 314.2 mm²
σ = P/A = 45·1000/314.2 = 143.2 MPa

Strain (Hooke’s law)

E for copper = 117 GPa = 117000 MPa.

ε = σ/E = 143.2/117000 = 0.001224 = 1224 µε

Elongation

δ = ε·L = 0.001224·2000 mm = 2.449 mm

Answer

δ = 2.449 mm
8.Axial stress & strain

Answer: σ2 = 38.58 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·314.2/400 = 157080 N/mm
k₂ = 100000·1963/400 = 490874 N/mm

Share of segment 2

F2 = 100000·490874/647953 = 75758 N

Stress

σ2 = 75758/1963 = 38.58 MPa (compression)

Answer

σ2 = 38.58 MPa
9.Column buckling

Answer: Pcr = 3.29 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 40·20³/12 = 26667 mm⁴

Effective length

KL = 2·2000 = 4000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·26667/4000² = 3290 N = 3.29 kN

Answer

Pcr = 3.29 kN
10.Column buckling

Answer: σcr = 24.87 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·60⁴/64 = 636173 mm⁴

Radius of gyration and slenderness

A = 2827 mm²
r = √(I/A) = √(636173/2827) = 15 mm
KL = 1·2500 = 2500 mm
KL/r = 2500/15 = 166.7

Critical stress

σcr = π²E/(KL/r)² = π²·70000/166.7² = 24.87 MPa

Answer

σcr = 24.87 MPa
11.Mechanical vibrations

Answer: fd = 14.21 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Undamped natural frequency

ωn = √(150000/15) = 100 rad/s
fn = 100/(2π) = 15.92 Hz

Damped natural frequency

fd = fn·√(1 − ζ²) = 15.92·√(1 − 0.45²) = 14.21 Hz

Answer

fd = 14.21 Hz
12.Mechanical vibrations

Answer: fn = 3.446 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/50 + 1/30 → keq = 50·30/(50 + 30) = 18.75 kN/m

Natural frequency

ωn = √(18750/40) = 21.65 rad/s
fn = 21.65/(2π) = 3.446 Hz

Answer

fn = 3.446 Hz

ExamProblems · examproblems.com/courses/machine-design