Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
An 11 kW motor running at 960 rpm drives a pinion with 50 teeth, which meshes with a gear with 72 teeth. The gear pair has an efficiency of 97%. Find the torque T1 on the motor shaft.
A 3 kW motor at 2900 rpm drives gear A (15 teeth), which meshes with gear B (36 teeth). Gear C (15 teeth) on the same shaft as B drives gear D (80 teeth) on the output shaft. Each gear mesh has an efficiency of 98%. Find the output torque Tout.
A solid brass shaft 1 m long carries a torque of 400 N·m. The angle of twist between its ends must not exceed 2°. Find the smallest diameter d that meets this limit.
A hollow shaft must transmit 30 kW at 1450 rpm. Its inner diameter is to be 0.75 times its outer diameter, and the shear stress must not exceed 60 MPa. Find the smallest outer diameter do.
A point in a loaded part has σₓ = 60 MPa, σᵧ = 100 MPa and τₓᵧ = −10 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A point in a loaded part has σₓ = 40 MPa, σᵧ = −60 MPa and τₓᵧ = 30 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 40° counter-clockwise from the x-axis (positive in the same sense as τₓᵧ).
A steel rod (diameter 20 mm, E = 200 GPa) sits inside a tube made of aluminium (outer diameter 100 mm, inner diameter 70 mm, E = 70 GPa). Both are 400 mm long and are compressed together between rigid plates by 250 kN. Find the shortening δ.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of steel is fixed at the base and free at the top. It must carry 55 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.
A 40 kg mass is supported by a spring with a stiffness of 8 kN/m and a viscous damper with a damping coefficient of 170 N·s/m. Find the damping ratio ζ.
A 20 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 80 kN/m and k₂ = 60 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: T1 = 109.4 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: Tout = 121.4 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: d = 41.59 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: do = 29.06 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
A solid shaft would need d = 25.6 mm; the hollow one is a little larger but much lighter.
Answer: τmax = 22.36 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: τθ = −44.03 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.2914 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: δ = 0.4742 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 3.598 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: d = 97.62 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 327.8, so the column is slender and Euler applies.
Answer: ζ = 0.1503
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: keq = 140 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design