Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
Tw​ = ?z = 2, 1440 rpm

A 0.37 kW motor at 1440 rpm drives a worm with 2 start(s). The worm wheel has 30 teeth and the drive has an efficiency of 80%. Find the output torque Tw on the wheel shaft.

z = 2Nw = 30n = 1440 rpmP = 0.37 kWη = 80%
Tw = N·m
2.Gears & gear trainsHard
Ns​ = 24ring fixedNp​ = 12nc​ = ?

In a planetary gear set the sun gear has 24 teeth and each planet gear has 12 teeth. The ring gear is held fixed and the sun is driven at 600 rpm. Find the speed nc of the planet carrier.

Ns = 24Np = 12ns = 600 rpm
nc = rpm
3.Torsion of shaftsMedium
d1​ = 40 mmd2​ = 30 mmT = 250 N·mABC1.5 m3 m

A stepped solid steel shaft is fixed at A. Segment AB has diameter 40 mm and length 1.5 m; segment BC has diameter 30 mm and length 3 m. A torque of 250 N·m acts at the free end C. Find the maximum shear stress τmax in the shaft.

T = 250 N·md1 = 40 mm, L1 = 1.5 md2 = 30 mm, L2 = 3 m
τmax = MPa
4.Torsion of shaftsHard
Td = ?

A solid shaft must transmit 100 kW at 750 rpm without the shear stress exceeding 60 MPa. Find the smallest diameter d that works.

P = 100 kWN = 750 rpmτallow = 60 MPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = 130σy​ = −70τxy​ = 40MPa

A point has σₓ = 130 MPa, σᵧ = −70 MPa and τₓᵧ = 40 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).

σx = 130 MPaσy = −70 MPaτxy = 40 MPa
θs = °
6.Mohr’s circle & stress transformationHard
σx​ = 40σy​ = −50τxy​ = 50MPa

A point in a loaded part has σₓ = 40 MPa, σᵧ = −50 MPa and τₓᵧ = 50 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 45° clockwise from the x-axis (positive in the same sense as τₓᵧ).

σx = 40 MPaσy = −50 MPaτxy = 50 MPaθ = -45°
τθ = MPa
7.Axial stress & strainMedium
Ø 20 mmSteel2 mP = 55 kN

Find the elongation δ of the steel bar under the axial load.

P = 55 kNd = 20 mmL = 2 mE = 200 GPa
δ = mm
8.Axial stress & strainHard
20 kN12600 mm300 mmØ20Ø30σ2​ = ?

A steel segment (diameter 20 mm, length 600 mm, E = 200 GPa) and a segment made of aluminium (diameter 30 mm, length 300 mm, E = 70 GPa) are joined end to end and fixed between two rigid walls. An axial load of 20 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø20 mm, 600 mm, E = 200 GPasegment 2: aluminium, Ø30 mm, 300 mm, E = 70 GPaP = 20 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2 md = 20 mmcross-section

A column of length L made of aluminium is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 2 mE = 70 GPa (aluminium)d = 20 mm
Pcr = kN
10.Column bucklingHard
PL = 4 md = 80 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 4 mE = 200 GPa (steel)d = 80 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx30 mm2 cycles10.9 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 30 mm is followed 2 cycles later by a peak of 10.9 mm. Find the damping ratio ζ.

x0 = 30 mmx2 = 10.9 mmn = 2
ζ =
12.Mechanical vibrationsHard
k1​ = 10k2​ = 20k3​ = 30m = 5 kg

A 5 kg mass hangs from spring k₃ = 30 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 10 kN/m and k₂ = 20 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 5 kgk1 = 10 kN/mk2 = 20 kN/mk3 = 30 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: Tw = 29.44 N·m

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Wheel speed

nw = n·z/Nw = 1440·2/30 = 96 rpm

Output torque

ωw = 2π·96/60 = 10.05 rad/s
Tw = η·P/ωw = 0.8·370/10.05 = 29.44 N·m

Answer

Tw = 29.44 N·m
2.Gears & gear trains

Answer: nc = 200 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 24 + 2·12 = 48

Willis equation with the ring fixed

Set nr = 0 and solve for the carrier speed.

(600 − nc)/(0 − nc) = −48/24
nc = ns·Ns/(Ns + Nr) = 600·24/72 = 200 rpm

Answer

nc = 200 rpm

The carrier turns in the same direction as the sun.

3.Torsion of shafts

Answer: τmax = 47.16 MPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Stress in each segment

T = 250 N·m = 250000 N·mm
τAB = 16·250000/(π·40³) = 19.89 MPa
τBC = 16·250000/(π·30³) = 47.16 MPa

Answer

τmax = 47.16 MPa
4.Torsion of shafts

Answer: d = 47.63 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·750/60 = 78.54 rad/s
T = P/ω = 100000/78.54 = 1273 N·m

Diameter from the allowable stress

d = ∛(16T/(π·τallow)) = ∛(16·1.273 × 10⁶/(π·60)) = 47.63 mm

Answer

d = 47.63 mm

In practice you would round up to the next standard size.

5.Mohr’s circle & stress transformation

Answer: θs = −34.1 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Angle on the circle

On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.

cos 2θs = 40/107.7 = 0.3714, sin 2θs = −100/107.7 = −0.9285
2θs = atan2(−100, 40) = −68.2°

Angle on the element

θs = −34.1°
check: θs − θp = −34.1 − 10.9 = −45°

Answer

θs = −34.1°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: τθ = 45 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

τθ = −45·−1 + 50·0 = 45 MPa

Answer

τθ = 45 MPa
7.Axial stress & strain

Answer: δ = 1.751 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·20²/4 = 314.2 mm²
σ = P/A = 55·1000/314.2 = 175.1 MPa

Strain (Hooke’s law)

E for steel = 200 GPa = 200000 MPa.

ε = σ/E = 175.1/200000 = 0.0008754 = 875.4 µε

Elongation

δ = ε·L = 0.0008754·2000 mm = 1.751 mm

Answer

δ = 1.751 mm
8.Axial stress & strain

Answer: σ2 = 17.31 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·314.2/600 = 104720 N/mm
k₂ = 70000·706.9/300 = 164934 N/mm

Share of segment 2

F2 = 20000·164934/269653 = 12233 N

Stress

σ2 = 12233/706.9 = 17.31 MPa (compression)

Answer

σ2 = 17.31 MPa
9.Column buckling

Answer: Pcr = 2.768 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·20⁴/64 = 7854 mm⁴

Effective length

KL = 0.7·2000 = 1400 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·7854/1400² = 2768 N = 2.768 kN

Answer

Pcr = 2.768 kN
10.Column buckling

Answer: σcr = 12.34 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·80⁴/64 = 2.011 × 10⁶ mm⁴

Radius of gyration and slenderness

A = 5027 mm²
r = √(I/A) = √(2.011 × 10⁶/5027) = 20 mm
KL = 2·4000 = 8000 mm
KL/r = 8000/20 = 400

Critical stress

σcr = π²E/(KL/r)² = π²·200000/400² = 12.34 MPa

Answer

σcr = 12.34 MPa
11.Mechanical vibrations

Answer: ζ = 0.08031

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/2)·ln(30/10.9) = 0.5062

Damping ratio

ζ = δ/√(4π² + δ²) = 0.5062/√(39.48 + 0.2563) = 0.08031

Answer

ζ = 0.08031
12.Mechanical vibrations

Answer: fn = 8.717 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 10 + 20 = 30 kN/m
keq = 30·30/(30 + 30) = 15 kN/m

Natural frequency

ωn = √(15000/5) = 54.77 rad/s
fn = 54.77/(2π) = 8.717 Hz

Answer

fn = 8.717 Hz

ExamProblems · examproblems.com/courses/machine-design