Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 100 mmd2​ = 450 mm720 rpmT1​ = 1500 NT2​ = 750 NP = ?

A belt runs on a 100 mm driving pulley at 720 rpm. The tension is 1500 N on the tight side and 750 N on the slack side. Find the power P transmitted, in kW.

d1 = 100 mmn1 = 720 rpmT1 = 1500 NT2 = 750 N
P = kW
2.Gears & gear trainsHard
A = 20B = 32C = 16D = 25

A 1.5 kW motor at 1440 rpm drives gear A (20 teeth), which meshes with gear B (32 teeth). Gear C (16 teeth) on the same shaft as B drives gear D (25 teeth) on the output shaft. Each gear mesh has an efficiency of 97%. Find the output torque Tout.

P = 1.5 kWnin = 1440 rpmA = 20B = 32C = 16D = 25ηmesh = 97%
Tout = N·m
3.Torsion of shaftsMedium
d = ?T = 400 N·mL = 2.5 m

A solid steel shaft 2.5 m long carries a torque of 400 N·m. The angle of twist between its ends must not exceed 3°. Find the smallest diameter d that meets this limit.

T = 400 N·mL = 2.5 mG = 80 GPaφallow = 3°
d = mm
4.Torsion of shaftsHard
d = ?50 kW, 1000 rpm

A solid steel shaft transmits 50 kW at 1000 rpm. The shear stress must not exceed 80 MPa and the twist must not exceed 0.5° per m of length. Find the smallest diameter d that satisfies both limits.

P = 50 kWN = 1000 rpmτallow = 80 MPaθallow = 0.5°/mG = 80 GPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = 70σy​ = 20τxy​ = 20MPa

A point in a loaded part has σₓ = 70 MPa, σᵧ = 20 MPa and τₓᵧ = 20 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.

σx = 70 MPaσy = 20 MPaτxy = 20 MPa
θp = °
6.Mohr’s circle & stress transformationHard
40°D = 500 mm, t = 8 mm, p = 0.8 MPap

A thin-walled cylindrical tank of inner diameter 500 mm and wall thickness 8 mm holds gas at a gauge pressure of 0.8 MPa. It is made from plate welded along a helical seam at 40° to the axis of the cylinder. Find the normal stress σn acting across the weld seam.

D = 500 mmt = 8 mmp = 0.8 MPaα = 40°
σn = MPa
7.Axial stress & strainMedium
Ø 30 mmAluminium2 mP = 55 kN

Find the axial strain ε in the aluminium bar, in microstrain (µε = 10⁻⁶).

P = 55 kNd = 30 mmL = 2 mE = 70 GPa
ε = µε
8.Axial stress & strainHard
Ø 35 mmSteel2 mØ 12 mmSteel1 mP = 105 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.

P = 105 kNsegment 1: Ø35 mm, 2 m, steel (E = 200 GPa)segment 2: Ø12 mm, 1 m, steel (E = 200 GPa)
δ = mm
9.Column bucklingMedium
PL = 5 m50 × 100 mmcross-section

A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 5 mE = 200 GPa (steel)b × h = 50 × 100 mm
Pcr = kN
10.Column bucklingHard
PL = 1.5 md = 25 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 1.5 mE = 200 GPa (steel)d = 25 mm
σcr = MPa
11.Mechanical vibrationsMedium
k = 80 kN/mζ = 0.5m = 50 kg

A 50 kg mass on a spring with a stiffness of 80 kN/m has a viscous damper giving a damping ratio of 0.5. Find the damped natural frequency fd of its free vibration in Hz.

m = 50 kgk = 80 kN/mζ = 0.5
fd = Hz
12.Mechanical vibrationsHard
k1​ = 60k2​ = 50m = 50 kg

A 50 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 60 kN/m and k₂ = 50 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 50 kgk1 = 60 kN/mk2 = 50 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 2.827 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 3.77 m/s

Power

P = (1500 − 750)·3.77 = 2827 W = 2.827 kW

Answer

P = 2.827 kW
2.Gears & gear trains

Answer: Tout = 23.4 N·m

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Output speed

nout = 1440·(20/32)·(16/25) = 576 rpm
ωout = 2π·576/60 = 60.32 rad/s

Output power and torque

Pout = 1500·0.97² = 1411 W
Tout = Pout/ωout = 1411/60.32 = 23.4 N·m

Answer

Tout = 23.4 N·m
3.Torsion of shafts

Answer: d = 39.49 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Required polar moment

T = 400 N·m = 400000 N·mm
L = 2.5 m = 2500 mm
G = 80 GPa = 80000 MPa
φ = 3·π/180 = 0.05236 rad
J = TL/(Gφ) = 400000·2500/(80000·0.05236) = 238732 mm⁴

Diameter

d = (32J/π)1/4 = 39.49 mm

Answer

d = 39.49 mm

In practice you would round up to the next standard size.

4.Torsion of shafts

Answer: d = 51.37 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·1000/60 = 104.7 rad/s
T = P/ω = 50000/104.7 = 477.5 N·m

Diameter for strength

T = 477.5 N·m = 477465 N·mm
dτ = ∛(16·477465/(π·80)) = 31.21 mm

Diameter for stiffness

θ = 0.5·π/180/1000 = 8.727 × 10⁻⁶ rad/mm
G = 80 GPa = 80000 MPa
dφ = (32·477465/(π·80000·8.727 × 10⁻⁶))1/4 = 51.37 mm

Governing diameter

Both limits must hold, so the larger diameter governs.

d = max(31.21, 51.37) = 51.37 mm

Answer

d = 51.37 mm

Here stiffness governs.

5.Mohr’s circle & stress transformation

Answer: θp = 19.33 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCσ1​σ2​

Angle on the circle

Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.

2θp = atan2(2·20, 70 − 20) = 38.66°

Angle on the element

θp = 19.33°

Answer

θp = 19.33°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: σn = 19.84 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Thin-walled cylinder: hoop stress σh = pr/t and axial stress σa = pr/(2t); these are the principal stresses in the wall.

Wall stresses

r = 500/2 = 250 mm
σh = pr/t = 0.8·250/8 = 25 MPa
σa = pr/(2t) = 12.5 MPa

Transform to the seam

Take x along the axis (σa) and y around the hoop (σh). The seam’s normal makes 90° − α with the axis.

σn = 12.5·sin²40° + 25·cos²40° = 19.84 MPa

Answer

σn = 19.84 MPa
7.Axial stress & strain

Answer: ε = 1112 µε

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·30²/4 = 706.9 mm²
σ = P/A = 55·1000/706.9 = 77.81 MPa

Strain (Hooke’s law)

E for aluminium = 70 GPa = 70000 MPa.

ε = σ/E = 77.81/70000 = 0.001112 = 1112 µε

Answer

ε = 1112 µε
8.Axial stress & strain

Answer: δ = 5.733 mm

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·35²/4 = 962.1 mm², A2 = π·12²/4 = 113.1 mm²
σ1 = 109.1 MPa
σ2 = 928.4 MPa

Add the segment elongations

δ1 = σ1L1/E1 = 109.1·2000/200000 = 1.091 mm
δ2 = σ2L2/E2 = 928.4·1000/200000 = 4.642 mm
δ = δ1 + δ2 = 5.733 mm

Answer

δ = 5.733 mm
9.Column buckling

Answer: Pcr = 82.25 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 100·50³/12 = 1.042 × 10⁶ mm⁴

Effective length

KL = 1·5000 = 5000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·1.042 × 10⁶/5000² = 82247 N = 82.25 kN

Answer

Pcr = 82.25 kN
10.Column buckling

Answer: σcr = 8.567 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Radius of gyration and slenderness

A = 490.9 mm²
r = √(I/A) = √(19175/490.9) = 6.25 mm
KL = 2·1500 = 3000 mm
KL/r = 3000/6.25 = 480

Critical stress

σcr = π²E/(KL/r)² = π²·200000/480² = 8.567 MPa

Answer

σcr = 8.567 MPa
11.Mechanical vibrations

Answer: fd = 5.513 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Undamped natural frequency

ωn = √(80000/50) = 40 rad/s
fn = 40/(2π) = 6.366 Hz

Damped natural frequency

fd = fn·√(1 − ζ²) = 6.366·√(1 − 0.5²) = 5.513 Hz

Answer

fd = 5.513 Hz
12.Mechanical vibrations

Answer: fn = 7.465 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.

keq = 60 + 50 = 110 kN/m

Natural frequency

ωn = √(110000/50) = 46.9 rad/s
fn = 46.9/(2π) = 7.465 Hz

Answer

fn = 7.465 Hz

ExamProblems · examproblems.com/courses/machine-design