Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 150 mmd2​ = 300 mm1450 rpmT1​ = 800 NT2​ = 400 NP = ?

A belt runs on a 150 mm driving pulley at 1450 rpm. The tension is 800 N on the tight side and 400 N on the slack side. Find the power P transmitted, in kW.

d1 = 150 mmn1 = 1450 rpmT1 = 800 NT2 = 400 N
P = kW
2.Gears & gear trainsHard
d1​ = 150 mmd2​ = 300 mm960 rpmC = 500 mmθ = ?

An open belt connects a 150 mm pulley and a 300 mm pulley whose centres are 500 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.

d1 = 150 mmd2 = 300 mmC = 500 mm
θ = °
3.Torsion of shaftsMedium
d1​ = 60 mmd2​ = 25 mmT = 500 N·mABC3 m0.8 m

A stepped solid brass shaft is fixed at A. Segment AB has diameter 60 mm and length 3 m; segment BC has diameter 25 mm and length 0.8 m. A torque of 500 N·m acts at the free end C. Find the maximum shear stress τmax in the shaft.

T = 500 N·md1 = 60 mm, L1 = 3 md2 = 25 mm, L2 = 0.8 m
τmax = MPa
4.Torsion of shaftsHard
d = 25 mmT0​ = 500 N·mACBa = 2.5 mb = 1 m

A solid steel shaft of diameter 25 mm is fixed to rigid walls at both ends A and B. A torque of 500 N·m is applied at C, 2.5 m from A and 1 m from B. Find the maximum shear stress τmax in the shaft.

d = 25 mmT0 = 500 N·ma = 2.5 mb = 1 m
τmax = MPa
5.Mohr’s circle & stress transformationMedium
σx​ = −10σy​ = 30τxy​ = 30MPa

A point in a loaded part has σₓ = −10 MPa, σᵧ = 30 MPa and τₓᵧ = 30 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.

σx = −10 MPaσy = 30 MPaτxy = 30 MPa
θp = °
6.Mohr’s circle & stress transformationHard
35°D = 500 mm, t = 6 mm, p = 2.5 MPap

A thin-walled cylindrical tank of inner diameter 500 mm and wall thickness 6 mm holds gas at a gauge pressure of 2.5 MPa. It is made from plate welded along a helical seam at 35° to the axis of the cylinder. Find the normal stress σn acting across the weld seam.

D = 500 mmt = 6 mmp = 2.5 MPaα = 35°
σn = MPa
7.Axial stress & strainMedium
Ø 12 mmCopper1 mP = 105 kN

Find the elongation δ of the copper bar under the axial load.

P = 105 kNd = 12 mmL = 1 mE = 117 GPa
δ = mm
8.Axial stress & strainHard
Ø 40 mmBrass2 mØ 12 mmSteel2 mP = 80 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.

P = 80 kNsegment 1: Ø40 mm, 2 m, brass (E = 100 GPa)segment 2: Ø12 mm, 2 m, steel (E = 200 GPa)
σmax = MPa
9.Column bucklingMedium
PL = 3 m50 × 80 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 3 mE = 200 GPa (steel)b × h = 50 × 80 mm
Pcr = kN
10.Column bucklingHard
P = 65 kNL = 4 md = ?cross-section

A solid round column of length L made of aluminium is fixed at the base and pinned at the top. It must carry 65 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.

P = 65 kNn = 2L = 4 mE = 70 GPa (aluminium)
d = mm
11.Mechanical vibrationsMedium
k = 50 kN/mζ = 0.6m = 50 kg

A 50 kg mass on a spring with a stiffness of 50 kN/m has a viscous damper giving a damping ratio of 0.6. Find the damped natural frequency fd of its free vibration in Hz.

m = 50 kgk = 50 kN/mζ = 0.6
fd = Hz
12.Mechanical vibrationsHard
k1​ = 5k2​ = 100m = 10 kg

A 10 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 5 kN/m and k₂ = 100 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 10 kgk1 = 5 kN/mk2 = 100 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 4.555 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 11.39 m/s

Power

P = (800 − 400)·11.39 = 4555 W = 4.555 kW

Answer

P = 4.555 kW
2.Gears & gear trains

Answer: θ = 162.7 °

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt angle

asin(0.15) = 8.627°

Angle of wrap

θ = 180 − 2·8.627 = 162.7°

Answer

θ = 162.7°
3.Torsion of shafts

Answer: τmax = 163 MPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Stress in each segment

T = 500 N·m = 500000 N·mm
τAB = 16·500000/(π·60³) = 11.79 MPa
τBC = 16·500000/(π·25³) = 163 MPa

Answer

τmax = 163 MPa
4.Torsion of shafts

Answer: τmax = 116.4 MPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).

Equilibrium and compatibility

TA + TB = 500
TA·a = TB·b
TA = 500·1/3.5 = 142.9 N·m
TB = 500·2.5/3.5 = 357.1 N·m

Maximum shear stress

The larger of the two torques governs (same diameter).

τmax = 16·357143/(π·25³) = 116.4 MPa

Answer

τmax = 116.4 MPa
5.Mohr’s circle & stress transformation

Answer: θp = 61.85 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCσ1​σ2​

Angle on the circle

Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.

2θp = atan2(2·30, −10 − 30) = 123.7°

Angle on the element

θp = 61.85°

Answer

θp = 61.85°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: σn = 87.03 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Thin-walled cylinder: hoop stress σh = pr/t and axial stress σa = pr/(2t); these are the principal stresses in the wall.

Wall stresses

r = 500/2 = 250 mm
σh = pr/t = 2.5·250/6 = 104.2 MPa
σa = pr/(2t) = 52.08 MPa

Transform to the seam

Take x along the axis (σa) and y around the hoop (σh). The seam’s normal makes 90° − α with the axis.

σn = 52.08·sin²35° + 104.2·cos²35° = 87.03 MPa

Answer

σn = 87.03 MPa
7.Axial stress & strain

Answer: δ = 7.935 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·12²/4 = 113.1 mm²
σ = P/A = 105·1000/113.1 = 928.4 MPa

Strain (Hooke’s law)

E for copper = 117 GPa = 117000 MPa.

ε = σ/E = 928.4/117000 = 0.007935 = 7935 µε

Elongation

δ = ε·L = 0.007935·1000 mm = 7.935 mm

Answer

δ = 7.935 mm
8.Axial stress & strain

Answer: σmax = 707.4 MPa

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·40²/4 = 1257 mm², A2 = π·12²/4 = 113.1 mm²
σ1 = 63.66 MPa
σ2 = 707.4 MPa

Largest stress

The thinner segment has the smaller area, so it carries the larger stress.

σmax = 707.4 MPa

Answer

σmax = 707.4 MPa
9.Column buckling

Answer: Pcr = 45.69 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 80·50³/12 = 833333 mm⁴

Effective length

KL = 2·3000 = 6000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·833333/6000² = 45693 N = 45.69 kN

Answer

Pcr = 45.69 kN
10.Column buckling

Answer: d = 74.04 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2·65000 = 130000 N
KL = 0.7·4000 = 2800 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·130000·2800²/(π³·70000))^(1/4) = 74.04 mm

Answer

d = 74.04 mm

Check: the slenderness KL/r is 151.3, so the column is slender and Euler applies.

11.Mechanical vibrations

Answer: fd = 4.026 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Undamped natural frequency

ωn = √(50000/50) = 31.62 rad/s
fn = 31.62/(2π) = 5.033 Hz

Damped natural frequency

fd = fn·√(1 − ζ²) = 5.033·√(1 − 0.6²) = 4.026 Hz

Answer

fd = 4.026 Hz
12.Mechanical vibrations

Answer: fn = 16.31 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.

keq = 5 + 100 = 105 kN/m

Natural frequency

ωn = √(105000/10) = 102.5 rad/s
fn = 102.5/(2π) = 16.31 Hz

Answer

fn = 16.31 Hz

ExamProblems · examproblems.com/courses/machine-design