Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
N1​ = 20N2​ = 40

A 5.5 kW motor running at 1440 rpm drives a pinion with 20 teeth, which meshes with a gear with 40 teeth. The gear pair has an efficiency of 95%. Find the torque T1 on the motor shaft.

P = 5.5 kWn1 = 1440 rpmN1 = 20N2 = 40η = 95%
T1 = N·m
2.Gears & gear trainsHard
d1​ = 160 mmd2​ = 400 mm2880 rpmC = 600 mmT1​ = 1000 NT2​P = ?

An open belt connects a 160 mm driving pulley at 2880 rpm to a 400 mm pulley; the centres are 600 mm apart. The coefficient of friction is 0.35 and the tight-side tension may not exceed 1000 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).

d1 = 160 mmn1 = 2880 rpmd2 = 400 mmC = 600 mmμ = 0.35T1 = 1000 N
P = kW
3.Torsion of shaftsMedium
T = 400 N·md = 25 mmL = 2.5 mφ = ?

A solid steel shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 400 N·md = 25 mmL = 2.5 mG = 80 GPa
φ = °
4.Torsion of shaftsHard
d = 60 mmT0​ = 100 N·mACBa = 1.5 mb = 2.5 m

A solid brass shaft of diameter 60 mm is fixed to rigid walls at both ends A and B. A torque of 100 N·m is applied at C, 1.5 m from A and 2.5 m from B. Find the angle of rotation φC of section C, in degrees.

d = 60 mmT0 = 100 N·ma = 1.5 mb = 2.5 mG = 39 GPa
φC = °
5.Mohr’s circle & stress transformationMedium
σx​ = −20σy​ = −80τxy​ = 30MPa

A point in a thin plate is in plane stress: σₓ = −20 MPa, σᵧ = −80 MPa and τₓᵧ = 30 MPa, with σz = 0. Find the absolute maximum shear stress τabs at the point (considering all planes in three dimensions).

σx = −20 MPaσy = −80 MPaτxy = 30 MPaσz = 0
τabs = MPa
6.Mohr’s circle & stress transformationHard
σx​ = 140σy​ = 80τxy​ = 40MPa

A point in a thin plate is in plane stress: σₓ = 140 MPa, σᵧ = 80 MPa and τₓᵧ = 40 MPa (σz = 0). The material has a yield strength of 300 MPa. Find the factor of safety n against yielding by the Tresca (maximum shear stress) criterion.

σx = 140 MPaσy = 80 MPaτxy = 40 MPaσY = 300 MPa
n =
7.Axial stress & strainMedium
P = ?12400 mm500 mmØ20Ø60δ = 0.2 mm

A bar is made of a steel segment (diameter 20 mm, length 400 mm, E = 200 GPa) joined end to end with a segment made of bronze (diameter 60 mm, length 500 mm, E = 110 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.2 mm in total.

segment 1: steel, Ø20 mm, 400 mm, E = 200 GPasegment 2: bronze, Ø60 mm, 500 mm, E = 110 GPaδ = 0.2 mm
P = kN
8.Axial stress & strainHard
20 kN12400 mm500 mmØ30Ø30σ2​ = ?

A steel segment (diameter 30 mm, length 400 mm, E = 200 GPa) and a segment made of copper (diameter 30 mm, length 500 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 20 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø30 mm, 400 mm, E = 200 GPasegment 2: copper, Ø30 mm, 500 mm, E = 120 GPaP = 20 kN
σ2 = MPa
9.Column bucklingMedium
PL = 1.5 m30 × 60 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 1.5 mE = 70 GPa (aluminium)b × h = 30 × 60 mm
Pcr = kN
10.Column bucklingHard
PL = 2.5 md = 30 mmcross-section

A column of length L made of steel is fixed at the base and pinned at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 2.5 mE = 200 GPa (steel)d = 30 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx20 mm5 cycles4.1 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 20 mm is followed 5 cycles later by a peak of 4.1 mm. Find the damping ratio ζ.

x0 = 20 mmx5 = 4.1 mmn = 5
ζ =
12.Mechanical vibrationsHard
k1​ = 15k2​ = 80m = 5 kg

A 5 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 15 kN/m and k₂ = 80 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 5 kgk1 = 15 kN/mk2 = 80 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: T1 = 36.47 N·m

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Motor torque

ω₁ = 2π·1440/60 = 150.8 rad/s
T1 = P/ω₁ = 5500/150.8 = 36.47 N·m

Answer

T1 = 36.47 N·m
2.Gears & gear trains

Answer: P = 14.88 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Angle of wrap

θ = 2.739 rad

Slack-side tension

eμθ = e0.9586 = 2.608, T₂ = 1000/2.608 = 383.4 N

Power

P = (1000 − 383.4)·24.13 = 14.88 kW

Answer

P = 14.88 kW
3.Torsion of shafts

Answer: φ = 18.68 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·25⁴/32 = 38350 mm⁴

Angle of twist

φ = TL/(GJ) = 400·1000·2500/(80000·38350) = 0.3259 rad
φ = 0.3259·180/π = 18.68°

Answer

φ = 18.68°
4.Torsion of shafts

Answer: φC = 0.1082 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).

Equilibrium and compatibility

TA + TB = 100
TA·a = TB·b
TA = 100·2.5/4 = 62.5 N·m
TB = 100·1.5/4 = 37.5 N·m

Rotation of C

Use segment AC: it is fixed at A and carries TA.

J = π·60⁴/32 = 1.272 × 10⁶ mm⁴
G = 39 GPa = 39000 MPa
φC = TA·a/(GJ) = 62500·1500/(39000·1.272 × 10⁶) = 0.001889 rad = 0.1082°

Answer

φC = 0.1082°
5.Mohr’s circle & stress transformation

Answer: τabs = 46.21 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. In three dimensions the absolute maximum shear stress is (σmax − σmin)/2 over all three principal stresses; in plane stress the third one is zero.

στxyCσ1​σ2​

In-plane principal stresses

C = −50 MPa, R = √(30² + 30²) = 42.43 MPa
σ1 = −7.574 MPa, σ2 = −92.43 MPa, σz = 0

Largest of the three circles

τ = max(|σ1 − σ2|, |σ1|, |σ2|)/2 = max(84.85, 7.574, 92.43)/2 = 46.21 MPa

Answer

τabs = 46.21 MPa

Here the out-of-plane circle governs: the absolute maximum is larger than the in-plane maximum R.

6.Mohr’s circle & stress transformation

Answer: n = 1.875

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.

στxyCσ1​σ2​

Principal stresses

C = 110 MPa, R = 50 MPa
σ1 = 160 MPa, σ2 = 60 MPa, σ3 = 0

Tresca

σmax − σmin = 160 MPa
n = 300/160 = 1.875

Answer

n = 1.875

n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.

7.Axial stress & strain

Answer: P = 25.08 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

A₁ = 314.2 mm², A₂ = 2827 mm²

Flexibilities

L₁/(E₁A₁) = 400/(200000·314.2) = 6.366 × 10⁻⁶ mm/N
L₂/(E₂A₂) = 500/(110000·2827) = 1.608 × 10⁻⁶ mm/N

Load

P = 0.2/7.974 × 10⁻⁶ = 25082 N = 25.08 kN

Answer

P = 25.08 kN
8.Axial stress & strain

Answer: σ2 = 9.177 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·706.9/400 = 353429 N/mm
k₂ = 120000·706.9/500 = 169646 N/mm

Share of segment 2

F2 = 20000·169646/523075 = 6486 N

Stress

σ2 = 6486/706.9 = 9.177 MPa (compression)

Answer

σ2 = 9.177 MPa
9.Column buckling

Answer: Pcr = 10.36 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 60·30³/12 = 135000 mm⁴

Effective length

KL = 2·1500 = 3000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·135000/3000² = 10363 N = 10.36 kN

Answer

Pcr = 10.36 kN
10.Column buckling

Answer: σcr = 36.26 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·30⁴/64 = 39761 mm⁴

Radius of gyration and slenderness

A = 706.9 mm²
r = √(I/A) = √(39761/706.9) = 7.5 mm
KL = 0.7·2500 = 1750 mm
KL/r = 1750/7.5 = 233.3

Critical stress

σcr = π²E/(KL/r)² = π²·200000/233.3² = 36.26 MPa

Answer

σcr = 36.26 MPa
11.Mechanical vibrations

Answer: ζ = 0.05038

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/5)·ln(20/4.1) = 0.3169

Damping ratio

ζ = δ/√(4π² + δ²) = 0.3169/√(39.48 + 0.1005) = 0.05038

Answer

ζ = 0.05038
12.Mechanical vibrations

Answer: fn = 21.94 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.

keq = 15 + 80 = 95 kN/m

Natural frequency

ωn = √(95000/5) = 137.8 rad/s
fn = 137.8/(2π) = 21.94 Hz

Answer

fn = 21.94 Hz

ExamProblems · examproblems.com/courses/machine-design