Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 200 mmd2​ = 400 mm1440 rpmT1​ = 600 NT2​ = 120 NP = ?

A belt runs on a 200 mm driving pulley at 1440 rpm. The tension is 600 N on the tight side and 120 N on the slack side. Find the power P transmitted, in kW.

d1 = 200 mmn1 = 1440 rpmT1 = 600 NT2 = 120 N
P = kW
2.Gears & gear trainsHard
Ns​ = 30nr​ = ?Np​ = 18carrier fixed

In a planetary gear set the sun gear has 30 teeth and each planet gear has 18 teeth. The planet carrier is held fixed and the sun is driven at 1440 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 30Np = 18ns = 1440 rpm
nr = rpm
3.Torsion of shaftsMedium
d = ?T = 2000 N·mL = 1.5 m

A solid steel shaft 1.5 m long carries a torque of 2000 N·m. The angle of twist between its ends must not exceed 1.5°. Find the smallest diameter d that meets this limit.

T = 2000 N·mL = 1.5 mG = 80 GPaφallow = 1.5°
d = mm
4.Torsion of shaftsHard
d = 50 mmTB​ = 200 N·mTC​ = 2000 N·mABC2 m0.5 m

A solid aluminium shaft of diameter 50 mm is fixed at A. A torque of 200 N·m acts at B, 2 m from A, and a torque of 2000 N·m in the same direction acts at the free end C, a further 0.5 m along. Find the magnitude of the angle of twist φC of end C, in degrees.

d = 50 mmTB = 200 N·mTC = 2000 N·mAB = 2 mBC = 0.5 mG = 26 GPa
φC = °
5.Mohr’s circle & stress transformationMedium
σx​ = 80σy​ = 50MPaτxy​ = ?

A point has σₓ = 80 MPa and σᵧ = 50 MPa. How large can the shear stress τxy (magnitude) become before the largest principal stress reaches 105 MPa?

σx = 80 MPaσy = 50 MPaσ1 = 105 MPa
τxy = MPa
6.Mohr’s circle & stress transformationHard
σx​ = 100σy​ = 100τxy​ = 10MPa

A point in a loaded part has σₓ = 100 MPa, σᵧ = 100 MPa and τₓᵧ = 10 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 45° clockwise from the x-axis.

σx = 100 MPaσy = 100 MPaτxy = 10 MPaθ = -45°
σθ = MPa
7.Axial stress & strainMedium
Ø 12 mmCopper2 mP = 55 kN

Find the axial strain ε in the copper bar, in microstrain (µε = 10⁻⁶).

P = 55 kNd = 12 mmL = 2 mE = 117 GPa
ε = µε
8.Axial stress & strainHard
Ø 25 mmCopper1.5 mØ 20 mmBrass1.5 mP = 70 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.

P = 70 kNsegment 1: Ø25 mm, 1.5 m, copper (E = 117 GPa)segment 2: Ø20 mm, 1.5 m, brass (E = 100 GPa)
σmax = MPa
9.Column bucklingMedium
PL = 2.5 md = 20 mmcross-section

A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 2.5 mE = 200 GPa (steel)d = 20 mm
Pcr = kN
10.Column bucklingHard
P = 80 kNL = 2.5 md = ?cross-section

A solid round column of length L made of aluminium is fixed at the base and pinned at the top. It must carry 80 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.

P = 80 kNn = 2.5L = 2.5 mE = 70 GPa (aluminium)
d = mm
11.Mechanical vibrationsMedium
k = 40 kN/mc = 290 N·s/mm = 80 kg

An 80 kg mass is supported by a spring with a stiffness of 40 kN/m and a viscous damper with a damping coefficient of 290 N·s/m. Find the damping ratio ζ.

m = 80 kgk = 40 kN/mc = 290 N·s/m
ζ =
12.Mechanical vibrationsHard
k1​ = 10k2​ = 12k3​ = 60m = 10 kg

A 10 kg mass hangs from spring k₃ = 60 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 10 kN/m and k₂ = 12 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 10 kgk1 = 10 kN/mk2 = 12 kN/mk3 = 60 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 7.238 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 15.08 m/s

Power

P = (600 − 120)·15.08 = 7238 W = 7.238 kW

Answer

P = 7.238 kW
2.Gears & gear trains

Answer: nr = 654.5 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 30 + 2·18 = 66

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −1440·30/66 = −654.5 rpm
|nr| = 654.5 rpm

Answer

nr = 654.5 rpm

The ring turns opposite to the sun.

3.Torsion of shafts

Answer: d = 61.8 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Required polar moment

T = 2000 N·m = 2 × 10⁶ N·mm
L = 1.5 m = 1500 mm
G = 80 GPa = 80000 MPa
φ = 1.5·π/180 = 0.02618 rad
J = TL/(Gφ) = 2 × 10⁶·1500/(80000·0.02618) = 1.432 × 10⁶ mm⁴

Diameter

d = (32J/π)1/4 = 61.8 mm

Answer

d = 61.8 mm

In practice you would round up to the next standard size.

4.Torsion of shafts

Answer: φC = 19.39 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Internal torques

Sense of TC taken as positive.

TBC = TC = 2000 N·m
TAB = TC + TB = 2000 + 200 = 2200 N·m

Twist of each segment

J = π·50⁴/32 = 613592 mm⁴
G = 26 GPa = 26000 MPa
φAB = 2.2 × 10⁶·2000/(26000·613592) = 0.2758 rad
φBC = 2 × 10⁶·500/(26000·613592) = 0.06268 rad

Twist of end C

φC = 0.2758 + 0.06268 = 0.3385 rad → |φC| = 19.39°

Answer

φC = 19.39°
5.Mohr’s circle & stress transformation

Answer: τxy = 37.08 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Required radius

C = (80 + 50)/2 = 65 MPa
R = σ1 − C = 105 − 65 = 40 MPa
στxyCσ1​σ2​

Shear stress

τxy = √(R² − ((σₓ − σᵧ)/2)²) = √(40² − 15²) = 37.08 MPa

Answer

τxy = 37.08 MPa
6.Mohr’s circle & stress transformation

Answer: σθ = 90 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

σθ = 100 + 0·0 + 10·−1 = 90 MPa

Answer

σθ = 90 MPa
7.Axial stress & strain

Answer: ε = 4156 µε

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·12²/4 = 113.1 mm²
σ = P/A = 55·1000/113.1 = 486.3 MPa

Strain (Hooke’s law)

E for copper = 117 GPa = 117000 MPa.

ε = σ/E = 486.3/117000 = 0.004156 = 4156 µε

Answer

ε = 4156 µε
8.Axial stress & strain

Answer: σmax = 222.8 MPa

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·25²/4 = 490.9 mm², A2 = π·20²/4 = 314.2 mm²
σ1 = 142.6 MPa
σ2 = 222.8 MPa

Largest stress

The thinner segment has the smaller area, so it carries the larger stress.

σmax = 222.8 MPa

Answer

σmax = 222.8 MPa
9.Column buckling

Answer: Pcr = 9.922 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·20⁴/64 = 7854 mm⁴

Effective length

KL = 0.5·2500 = 1250 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·7854/1250² = 9922 N = 9.922 kN

Answer

Pcr = 9.922 kN
10.Column buckling

Answer: d = 65.19 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2.5·80000 = 200000 N
KL = 0.7·2500 = 1750 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·200000·1750²/(π³·70000))^(1/4) = 65.19 mm

Answer

d = 65.19 mm

Check: the slenderness KL/r is 107.4, so the column is slender and Euler applies.

11.Mechanical vibrations

Answer: ζ = 0.08106

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Critical damping

cc = 2·√(k·m) = 2·√(40000·80) = 3578 N·s/m

Damping ratio

ζ = c/cc = 290/3578 = 0.08106

Answer

ζ = 0.08106

ζ < 1, so the system is underdamped and oscillates as it decays.

12.Mechanical vibrations

Answer: fn = 6.386 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 10 + 12 = 22 kN/m
keq = 22·60/(22 + 60) = 16.1 kN/m

Natural frequency

ωn = √(16098/10) = 40.12 rad/s
fn = 40.12/(2π) = 6.386 Hz

Answer

fn = 6.386 Hz

ExamProblems · examproblems.com/courses/machine-design