Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 7.5 kW motor running at 960 rpm drives a pinion with 12 teeth, which meshes with a gear with 72 teeth. Ignore losses. Find the output torque T2 on the gear shaft.
In a planetary gear set the sun gear has 15 teeth and each planet gear has 24 teeth. The ring gear is held fixed and the sun is driven at 600 rpm. Find the speed nc of the planet carrier.
A solid steel shaft 1.5 m long carries a torque of 100 N·m. The angle of twist between its ends must not exceed 3°. Find the smallest diameter d that meets this limit.
A solid steel shaft transmits 30 kW at 1450 rpm. The shear stress must not exceed 50 MPa and the twist must not exceed 1° per m of length. Find the smallest diameter d that satisfies both limits.
A point has σₓ = 160 MPa, σᵧ = 50 MPa and τₓᵧ = −40 MPa (tension positive). The element is rotated 35° counter-clockwise. Find the normal stress σy′ on the faces of the rotated element that are perpendicular to the rotated y′-axis.
A thin-walled cylindrical tank of inner diameter 1000 mm and wall thickness 10 mm holds gas at a gauge pressure of 1 MPa. It is made from plate welded along a helical seam at 30° to the axis of the cylinder. Find the normal stress σn acting across the weld seam.
Find the elongation δ of the brass bar under the axial load.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of aluminium is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
An 8 kg mass is supported by a spring with a stiffness of 200 kN/m and a viscous damper with a damping coefficient of 1520 N·s/m. Find the damping ratio ζ.
A 100 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 25 kN/m and the lower one k₂ = 100 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: T2 = 447.6 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nc = 115.4 rpm
Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.
Set nr = 0 and solve for the carrier speed.
The carrier turns in the same direction as the sun.
Answer: d = 24.58 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: d = 34.65 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: σy′ = 123.8 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
The sum of the normal stresses does not change with rotation.
Answer: σn = 43.75 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Thin-walled cylinder: hoop stress σh = pr/t and axial stress σa = pr/(2t); these are the principal stresses in the wall.
Take x along the axis (σa) and y around the hoop (σh). The seam’s normal makes 90° − α with the axis.
Answer: δ = 0.2546 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for brass = 100 GPa = 100000 MPa.
Answer: δ = 4.276 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 3.052 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 77.11 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.6008
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 2.251 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design