Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 5.5 kW motor running at 1440 rpm drives a pinion with 24 teeth, which meshes with a gear with 80 teeth. The gear pair has an efficiency of 95%. Find the torque T1 on the motor shaft.
In a compound gear train, gear A (16 teeth) on the input shaft turning at 1450 rpm drives gear B (72 teeth). Gear C (25 teeth) is fixed to the same shaft as B and drives gear D (72 teeth) on the output shaft. Find the output speed nout.
A stepped solid steel shaft is fixed at A. Segment AB has diameter 40 mm and length 0.8 m; segment BC has diameter 30 mm and length 2 m. A torque of 400 N·m acts at the free end C. Find the maximum shear stress τmax in the shaft.
A solid aluminium shaft transmits 20 kW at 1450 rpm. The shear stress must not exceed 75 MPa and the twist must not exceed 1° per m of length. Find the smallest diameter d that satisfies both limits.
A point in a loaded part has σₓ = −20 MPa, σᵧ = −20 MPa and τₓᵧ = −20 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A point in a loaded part has σₓ = 160 MPa, σᵧ = 0 MPa and τₓᵧ = 60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 40° counter-clockwise from the x-axis.
Find the axial strain ε in the aluminium bar, in microstrain (µε = 10⁻⁶).
A steel rod (diameter 40 mm, E = 200 GPa, allowable stress 200 MPa) sits inside a tube made of copper (outer diameter 80 mm, inner diameter 50 mm, E = 120 GPa, allowable stress 50 MPa). They are compressed together between rigid plates. Find the largest load Pmax.
A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of aluminium is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
A 500 kg mass is supported by a spring with a stiffness of 200 kN/m and a viscous damper with a damping coefficient of 8000 N·s/m. Find the damping ratio ζ.
A 10 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 15 kN/m and k₂ = 12 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: T1 = 36.47 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 111.9 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 12.96 : 1
Answer: τmax = 75.45 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 41.47 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: τmax = 20 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: σθ = 153 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: ε = 4421 µε
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for aluminium = 70 GPa = 70000 MPa.
Answer: Pmax = 257.9 kN
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 62.01 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 6.218 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.4
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 8.27 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design