Mechatronic Systems: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

DC motors

Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc

Method

  1. Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
  2. Use V = E + Ia·Ra to link voltage, current and back-EMF.
  3. Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
  4. For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Data acquisition & sampling

Nyquist criterion
fs > 2·fmax, fN = fs/2
Alias frequency
fa = |f − k·fs|, k = round(f/fs)
Step size
1 LSB = VFSR/2ᴺ
Quantisation error (rounding)
±½ LSB
Truncating ADC code
D = ⌊Vin/LSB⌋
Bits for a resolution r
2ᴺ ≥ span/r
Ideal SQNR, full-scale sine
SQNR = 6.02·N + 1.76 dB
Data rate
channels × fs × N bit/s
Multiplexed ADC
fs = 1/(n·(tc + tset))
UART
Tb = 1/baud; 8N1 = 10 bits per byte; bytes/s = baud/bits per frame
Baud rate divider
baud = fclk/(16·D)

Method

  1. Write down what is given: sampling rate, signal frequencies, number of bits, input range, baud rate.
  2. For sampling questions, compare each frequency with fs/2; a higher frequency appears at fa = |f − k·fs| with the nearest multiple of fs.
  3. For resolution questions, find 1 LSB = VFSR/2ᴺ, or the smallest N with 2ᴺ ≥ span/resolution.
  4. For data rates and UART links, count everything that is sent: channels, samples per second, bits or whole bytes per sample, and the start, parity and stop bits of every frame.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Steady-state error & PID control

System type
number of poles of G(s) at s = 0
Error constants
Kp = lim G(s), Kv = lim s·G(s), Ka = lim s²·G(s) (s → 0)
Step A
ess = A/(1 + Kp)
Ramp A·t
ess = A/Kv
Parabola A·t²/2
ess = A/Ka
PID controller
C(s) = Kp + Ki/s + Kd·s
Second-order target
s² + 2ζωns + ωn²
Overshoot and timing
%OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd, ts ≈ 4/(ζωn)

Method

  1. Count the poles of the open loop C(s)·G(s) at s = 0: that is the system type.
  2. Work out the error constant that matches the input: Kp for a step, Kv for a ramp, Ka for a parabola.
  3. Apply ess = A/(1 + Kp), A/Kv or A/Ka, or solve it for the gain you need.
  4. For a damping or speed specification, write the closed-loop characteristic polynomial and match it with s² + 2ζω_n·s + ω_n².

2Practice problems

1.DC motorsMedium
+−VRa​M+−En = 750 rpmT = ?

A DC motor delivers 4 kW of mechanical power at 750 rpm. Find the shaft torque T.

P = 4 kWn = 750 rpm
T = N·m
2.DC motorsHard
+−240 VD = ?Ra​ = 1.2 ΩM+−En = 800 rpmT = 16 N·m

A DC chopper feeds a motor (k = 0.8 V·s/rad, Ra = 1.2 Ω) from a 240 V DC bus. The average armature voltage is D·240 V. Find the duty cycle D that runs the motor at 800 rpm with a load of 16 N·m.

Vdc = 240 Vk = 0.8 V·s/radRa = 1.2 ΩT = 16 N·mn = 800 rpm
D = %
3.Gears & gear trainsMedium
Nw​ = 40z = 1, 1450 rpm

A worm with 1 start(s) turns at 1450 rpm and drives a worm wheel with 40 teeth. Find the speed nw of the wheel.

z = 1Nw = 40n = 1450 rpm
nw = rpm
4.Gears & gear trainsHard
Ns​ = 16nr​ = ?Np​ = 12carrier fixed

In a planetary gear set the sun gear has 16 teeth and each planet gear has 12 teeth. The planet carrier is held fixed and the sun is driven at 600 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 16Np = 12ns = 600 rpm
nr = rpm
5.Data acquisition & samplingMedium
SD0​D1​D2​D3​D4​D5​D6​D7​Tb​11·Tb​4800 Bd, 8N2

A UART sends bytes at 4800 baud in the format 8N2: 8 data bits, no parity and 2 stop bit(s), plus the start bit. Find the largest number of data bytes per second it can transfer.

baud = 4800 Bd8N2
RB = B/s
6.Data acquisition & samplingHard
f0fs​/2fs​2.4 kHz5f₁?

A 2.4 kHz square wave is sampled at 20 kHz with no anti-aliasing filter. A square wave contains the odd harmonics 3f₁, 5f₁, 7f₁, … At which frequency fa does its harmonic 5f₁ appear in the sampled data? Give it in kHz.

f₁ = 2.4 kHzfs = 20 kHzharmonic: 5f₁
fa = kHz
7.Wheatstone bridge & strain gaugesMedium
+−10 VR1​ = 100 ΩR2​ = 80 ΩR3​ = 800 ΩR4​ = 800 ΩabGRg​ = 50 Ω

A galvanometer with a resistance of 50 Ω is connected between a and b of the bridge shown (Vs = 10 V). Find the galvanometer current Ig from a to b, in µA.

Vs = 10 VR1 = 100 ΩR2 = 80 ΩR3 = 800 ΩR4 = 800 ΩRg = 50 Ω
Ig = µA
8.Wheatstone bridge & strain gaugesHard
+−5 V120 Ω120 Ω + ΔR120 Ω120 Ωab+−1 mV

A strain gauge (GF = 2) on a member with E = 70 GPa forms a quarter bridge excited with 5 V. The output reads 1 mV. Find the axial stress σ in MPa.

Vs = 5 VGF = 2Vo = 1 mVE = 70 GPa
σ = MPa
9.Steady-state error & PID controlMedium
r(t) = 2 + 4t+2s(s + 2)C(s)−

The input r(t) = 2 + 4t (a step plus a ramp) is applied to a unity-feedback loop with G(s) = 2/(s(s + 2)). Find the steady-state error ess.

G(s) = 2/(s(s + 2))r(t) = 2 + 4t
ess =
10.Steady-state error & PID controlHard
R(s)+K = 255s(s + 10)C(s)−

A proportional controller K = 25 drives the plant G(s) = 5/(s(s + 10)) in a unity-feedback loop. Find the peak time tp of the step response.

G(s) = 5/(s(s + 10))K = 25
tp = s
11.Step responseMedium
t (s)y(t)2tp​ = ?

A system has the transfer function G(s) = 110/(s² + 11s + 55) and receives a unit step input. Find the peak time tp of the step response.

G(s) = 110/(s² + 11s + 55)
tp = s
12.Step responseHard
k = 2000 N/mc = 27 N·s/mm = 4 kgF = 100 Nx(t)

A mass m = 4 kg hangs on a spring k = 2000 N/m with a viscous damper c = 27 N·s/m (m·x″ + c·x′ + k·x = F). At rest in equilibrium, a constant force F = 100 N is suddenly applied. Find the damping ratio ζ.

m = 4 kgk = 2000 N/mc = 27 N·s/mF = 100 N
ζ =

3Solutions

1.DC motors

Answer: T = 50.93 N·m

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Speed in rad/s

ω = 2π·750/60 = 78.54 rad/s

Torque

T = P/ω = 4000/78.54 = 50.93 N·m

Answer

T = 50.93 N·m
2.DC motors

Answer: D = 37.93 %

DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.

Required armature voltage

Va = 0.8·83.78 + 20·1.2 = 91.02 V

Duty cycle

D = 91.02/240 = 37.93 %

Answer

D = 37.93 %
3.Gears & gear trains

Answer: nw = 36.25 rpm

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Wheel speed

nw = n·z/Nw = 1450·1/40 = 36.25 rpm

Answer

nw = 36.25 rpm
4.Gears & gear trains

Answer: nr = 240 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 16 + 2·12 = 40

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −600·16/40 = −240 rpm
|nr| = 240 rpm

Answer

nr = 240 rpm

The ring turns opposite to the sun.

5.Data acquisition & sampling

Answer: RB = 436.4 B/s

UART: an asynchronous serial link sends each byte as a frame: one start bit (low), the data bits, an optional parity bit and one or two stop bits (high). The baud rate is the number of bits per second, so one bit lasts Tb = 1/baud and a frame of n bits lasts n/baud. The common 8N1 format has 10 bits per byte. The baud generator divides the clock: baud = fclk/(16·D) with a whole number D, so the real baud rate differs slightly from the target; an error below about 2 % is usually acceptable.

Bits per frame

1 + 8 + 0 + 2 = 11

Byte rate

4800/11 = 436.4 B/s

Answer

RB = 436.4 B/s
6.Data acquisition & sampling

Answer: fa = 8 kHz

Sampling: an ADC measures the signal fs times per second. By the Nyquist–Shannon theorem a frequency f is captured correctly only while f < fs/2, the Nyquist (folding) frequency, so the sampling rate must exceed twice the highest signal frequency. A higher frequency is not lost: it shows up as an alias at fa = |f − k·fs|, with the whole number k that brings the result between 0 and fs/2. The samples cannot tell the two apart, so an analogue anti-aliasing filter must remove everything above fs/2 before the ADC.

Harmonic frequency

5f₁ = 5·2.4 kHz = 12 kHz

Nearest multiple of the sampling rate

m = round(0.6) = 1

Alias frequency

fa = |12 − 1·20| = 8 kHz

Answer

fa = 8 kHz

The alias lands inside the signal band, where no digital filter can remove it. Only an analogue filter before the ADC helps.

7.Wheatstone bridge & strain gauges

Answer: Ig = −1124 µA

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Thévenin voltage

Vth = 10·(80/180 − 800/1600) = −0.5556 V

Thévenin resistance

Rth = R₁∥R₂ + R₃∥R₄ = 444.4 Ω

Galvanometer current

Ig = −0.5556/(444.4 + 50) = −1124 µA

Answer

Ig = −1124 µA
8.Wheatstone bridge & strain gauges

Answer: σ = 28 MPa

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Strain

ε = 4·0.001/(5·2) = 0.0004

Stress

σ = 70·10³ MPa·0.0004 = 28 MPa

Answer

σ = 28 MPa
9.Steady-state error & PID control

Answer: ess = 4

Steady-state error: in a unity-feedback loop with open-loop transfer function G(s) the error is E(s) = R(s)/(1 + G(s)), and by the final value theorem ess = lims→0 s·E(s). The system type is the number of poles of G(s) at s = 0. The error constants are Kp = lim G(s), Kv = lim s·G(s) and Ka = lim s²·G(s), all for s → 0. A step of size A gives ess = A/(1 + Kp), a ramp A·t gives A/Kv and a parabola A·t²/2 gives A/Ka. A type-0 loop follows a step with a finite error, a type-1 loop follows it exactly and a ramp with a finite error.

Velocity constant

Kv = lim s·G(s) = 1

Step part

Kp = ∞ → estep = 0

Ramp error

ess = 4/1 = 4

Answer

ess = 4
10.Steady-state error & PID control

Answer: tp = 0.3142 s

P, PI and PID control: the controller C(s) = Kp + Ki/s + Kd·s acts on the error. A proportional gain makes the loop faster and reduces the error of a type-0 plant, but never removes it. The integral term adds a pole at s = 0: the system type rises by one, and a step is followed without error. The derivative term adds damping. To choose gains, write the closed-loop characteristic polynomial and compare it with s² + 2ζωns + ωn². Then %OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd with ωd = ωn√(1 − ζ²), and ts ≈ 4/(ζωn).

Characteristic polynomial

s(s + 10) + 25·5 = s² + 10s + 125

ωₙ and ζ

ωₙ = √125 = 11.18 rad/s
ζ = 10/(2·11.18) = 0.4472

Peak time

ωd = 11.18·√(1 − 0.4472²) = 10 rad/s
tp = π/10 = 0.3142 s

Answer

tp = 0.3142 s
11.Step response

Answer: tp = 0.6315 s

Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).

Compare with the standard form

The denominator must match s² + 2ζωₙs + ωₙ².

ωₙ² = 55 → ωₙ = 7.416 rad/s
2ζωₙ = 11 → ζ = 11/(2·7.416) = 0.7416

Result

ωd = 7.416·√(1 − 0.7416²) = 4.975 rad/s → tp = π/ωd = 0.6315 s

Answer

tp = 0.6315 s
12.Step response

Answer: ζ = 0.1509

Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).

Natural frequency and damping ratio

ωₙ = √(k/m) = √(2000/4) = 22.36 rad/s
ζ = c/(2√(km)) = 27/(2·√(2000·4)) = 0.1509

Result

ζ = 0.1509

Answer

ζ = 0.1509

ExamProblems · examproblems.com/courses/mechatronic-systems