In the print window, choose “Save as PDF” to keep a copy on your device.
1Formulas and methods
DC motors
Armature circuit
V = E + IaRa
Back-EMF and torque
E = k·ω, T = k·Ia
Speed
ω = 2π·n/60, ω = (V − IaRa)/k
No-load speed and stall torque
ω0 = V/k, Tstall = k·V/Ra
Powers
Pin = V·Ia, Pdev = E·Ia = T·ω, Pout = Pdev − Prot
Starting
Istart = V/(Ra + Rst)
Speed regulation
SR = (n0 − nFL)/nFL
Maximum developed power
Pmax = V²/(4Ra)
Chopper drive
Va = D·Vdc
Method
Draw the armature circuit: supply V, resistance Ra and the back-EMF E in series.
Use V = E + Ia·Ra to link voltage, current and back-EMF.
Use E = k·ω for speed and T = k·Ia for torque, with ω = 2π·n/60.
For power and efficiency, start from V·Ia, subtract the copper loss Ia²·Ra and then the rotational losses.
Gears & gear trains
Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios
Data acquisition & sampling
Nyquist criterion
fs > 2·fmax, fN = fs/2
Alias frequency
fa = |f − k·fs|, k = round(f/fs)
Step size
1 LSB = VFSR/2ᴺ
Quantisation error (rounding)
±½ LSB
Truncating ADC code
D = ⌊Vin/LSB⌋
Bits for a resolution r
2ᴺ ≥ span/r
Ideal SQNR, full-scale sine
SQNR = 6.02·N + 1.76 dB
Data rate
channels × fs × N bit/s
Multiplexed ADC
fs = 1/(n·(tc + tset))
UART
Tb = 1/baud; 8N1 = 10 bits per byte; bytes/s = baud/bits per frame
Baud rate divider
baud = fclk/(16·D)
Method
Write down what is given: sampling rate, signal frequencies, number of bits, input range, baud rate.
For sampling questions, compare each frequency with fs/2; a higher frequency appears at fa = |f − k·fs| with the nearest multiple of fs.
For resolution questions, find 1 LSB = VFSR/2ᴺ, or the smallest N with 2ᴺ ≥ span/resolution.
For data rates and UART links, count everything that is sent: channels, samples per second, bits or whole bytes per sample, and the start, parity and stop bits of every frame.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Steady-state error & PID control
System type
number of poles of G(s) at s = 0
Error constants
Kp = lim G(s), Kv = lim s·G(s), Ka = lim s²·G(s) (s → 0)
Step A
ess = A/(1 + Kp)
Ramp A·t
ess = A/Kv
Parabola A·t²/2
ess = A/Ka
PID controller
C(s) = Kp + Ki/s + Kd·s
Second-order target
s² + 2ζωns + ωn²
Overshoot and timing
%OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd, ts ≈ 4/(ζωn)
Method
Count the poles of the open loop C(s)·G(s) at s = 0: that is the system type.
Work out the error constant that matches the input: Kp for a step, Kv for a ramp, Ka for a parabola.
Apply ess = A/(1 + Kp), A/Kv or A/Ka, or solve it for the gain you need.
For a damping or speed specification, write the closed-loop characteristic polynomial and match it with s² + 2ζω_n·s + ω_n².
2Practice problems
1.DC motorsMedium
A DC motor draws 5 A from a 24 V supply. Its armature resistance is 0.25 Ω and its rotational (friction, windage and iron) losses are 6 W. Find its efficiency η.
V = 24 VIa = 5 ARa = 0.25 ΩProt = 6 W
η = %
2.DC motorsHard
A separately excited DC motor (k = 0.2 V·s/rad at full field, Ra = 1.2 Ω, V = 24 V) drives a constant load torque of 0.4 N·m. The field flux is reduced to 80 % of its full value. Find the new speed n.
Two parallel shafts are 78.75 mm apart. They must be connected by a pair of spur gears with a module of 1.5 mm and a speed reduction of 2.5 : 1. How many teeth N2 must the gear have?
a = 78.75 mmm = 1.5 mmi = 2.5
N2 =
4.Gears & gear trainsHard
In a compound gear train, gear A (15 teeth) on the input shaft turning at 2900 rpm drives gear B (48 teeth). Gear C (24 teeth) is fixed to the same shaft as B and drives gear D (50 teeth) on the output shaft. Find the output speed nout.
nin = 2900 rpmA = 15B = 48C = 24D = 50
nout = rpm
5.Data acquisition & samplingMedium
A recorder samples 8 channels at 1 kHz each with a 16-bit ADC. Each sample is stored in whole bytes. Find the memory M needed for a 15 min recording, in MB (1 MB = 10⁶ bytes).
n = 8fs = 1 kHzN = 16t = 15 min
M = MB
6.Data acquisition & samplingHard
A 15 kHz square wave is sampled at 50 kHz with no anti-aliasing filter. A square wave contains the odd harmonics 3f₁, 5f₁, 7f₁, … At which frequency fa does its harmonic 3f₁ appear in the sampled data? Give it in kHz.
f₁ = 15 kHzfs = 50 kHzharmonic: 3f₁
fa = kHz
7.Wheatstone bridge & strain gaugesMedium
A 470 Ω strain gauge is one arm (R₂) of a bridge with four equal 470 Ω arms and an excitation of 10 V. Find the power Pg dissipated in the gauge, in mW. Self-heating limits the excitation.
Vs = 10 VR = 470 Ω
Pg = mW
8.Wheatstone bridge & strain gaugesHard
A quarter bridge (one active gauge, GF = 2.1) is excited with 2.5 V. The largest strain to be measured is 250 µε, and it must give 5 V at the input of an analogue-to-digital converter. Find the amplifier gain G.
Vs = 2.5 VGF = 2.1εmax = 250 µεVFS = 5 V
G =
9.Steady-state error & PID controlMedium
The parabolic input r(t) = 0.5·t²/2 is applied to a unity-feedback loop with G(s) = 5(s + 4)/(s²(s + 5)). Find the steady-state error ess.
G(s) = 5(s + 4)/(s²(s + 5))r(t) = 0.5·t²/2
ess =
10.Steady-state error & PID controlHard
A PI controller C(s) = 2 + 2/s drives the plant G(s) = 2/((s + 2)(s + 10)) in a unity-feedback loop. Find the steady-state error ess for the ramp input r(t) = 2t.
C(s) = 2 + 2/sG(s) = 2/((s + 2)(s + 10))r(t) = 2t
ess =
11.Step responseMedium
A system has the transfer function G(s) = 50/(s² + 3s + 50) and receives a unit step input. The poles are s = σ ± jωd. Find the real part σ.
G(s) = 50/(s² + 3s + 50)
σ =
12.Step responseHard
A unity negative feedback loop has G(s) = K/(s(s + 16)). Find the gain K that gives a step response with 5 % overshoot.
G(s) = K/(s(s + 16))%OS = 5 %
K =
3Solutions
1.DC motors
Answer: η = 89.79 %
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Powers
Pin = 24·5 = 120 W
Pdev = 22.75·5 = 113.8 W
Pout = 113.8 − 6 = 107.8 W
Efficiency
η = 107.8/120·100 = 89.79 %
Answer
η = 89.79 %
2.DC motors
Answer: n = 1253 rpm
DC motor: the armature is a resistance Ra in series with the back-EMF E, so V = E + Ia·Ra. The back-EMF grows with speed, E = k·ω, and the torque with current, T = k·Ia, with the same motor constant k (V·s/rad = N·m/A) in SI units. Convert speeds with ω = 2π·n/60. The developed power is E·Ia = T·ω; the input power is V·Ia, and the copper loss Ia²Ra and the rotational loss make the difference. The speed falls in a straight line with torque, ω = V/k − Ra·T/k², from the no-load speed V/k to zero at the stall torque k·V/Ra. At standstill E = 0, so the starting current V/Ra is large unless a resistor limits it.
Field weakening is how a DC drive runs above its base speed.
3.Gears & gear trains
Answer: N2 = 75
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Total number of teeth
N1 + N2 = 2a/m = 2·78.75/1.5 = 105
Split by the ratio
N1 = 105/(1 + 2.5) = 30
N2 = 2.5·30 = 75
Answer
N2 = 75
4.Gears & gear trains
Answer: nout = 435 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
First stage
nB = 2900·15/48 = 906.3 rpm = nC
Second stage
nout = 906.3·24/50 = 435 rpm
Answer
nout = 435 rpm
total ratio = 6.667 : 1
5.Data acquisition & sampling
Answer: M = 14.4 MB
Data rates: every channel delivers fs samples per second of N bits, so the raw rate is channels × fs × N bit/s. In memory a sample takes whole bytes (a 12-bit sample is stored in 2 bytes), so the memory for a recording is channels × fs × bytes per sample × time. A multiplexed ADC converts the channels one after another: each conversion (with settling) takes t, so one round of n channels takes n·t and each channel is sampled at 1/(n·t).
Bytes per sample
⌈16/8⌉ = 2 B
Byte rate
8·1000·2 = 16000 B/s
Memory
M = 16000·900 = 1.44 × 10⁷ B = 14.4 MB
Answer
M = 14.4 MB
6.Data acquisition & sampling
Answer: fa = 5 kHz
Sampling: an ADC measures the signal fs times per second. By the Nyquist–Shannon theorem a frequency f is captured correctly only while f < fs/2, the Nyquist (folding) frequency, so the sampling rate must exceed twice the highest signal frequency. A higher frequency is not lost: it shows up as an alias at fa = |f − k·fs|, with the whole number k that brings the result between 0 and fs/2. The samples cannot tell the two apart, so an analogue anti-aliasing filter must remove everything above fs/2 before the ADC.
Harmonic frequency
3f₁ = 3·15 kHz = 45 kHz
Nearest multiple of the sampling rate
m = round(0.9) = 1
Alias frequency
fa = |45 − 1·50| = 5 kHz
Answer
fa = 5 kHz
The alias lands inside the signal band, where no digital filter can remove it. Only an analogue filter before the ADC helps.
7.Wheatstone bridge & strain gauges
Answer: Pg = 53.19 mW
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Voltage across the gauge
V = 10/2 = 5 V
Power
Pg = 5²/470 = 53.19 mW
Answer
Pg = 53.19 mW
8.Wheatstone bridge & strain gauges
Answer: G = 15238
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Bridge output at full scale
Vo = 0.3281 mV
Gain
G = 5/0.0003281 = 15238
Answer
G = 15238
9.Steady-state error & PID control
Answer: ess = 0.125
Steady-state error: in a unity-feedback loop with open-loop transfer function G(s) the error is E(s) = R(s)/(1 + G(s)), and by the final value theorem ess = lims→0 s·E(s). The system type is the number of poles of G(s) at s = 0. The error constants are Kp = lim G(s), Kv = lim s·G(s) and Ka = lim s²·G(s), all for s → 0. A step of size A gives ess = A/(1 + Kp), a ramp A·t gives A/Kv and a parabola A·t²/2 gives A/Ka. A type-0 loop follows a step with a finite error, a type-1 loop follows it exactly and a ramp with a finite error.
Acceleration constant
Ka = 5·4/5 = 4
Parabola error
ess = 0.5/4 = 0.125
Answer
ess = 0.125
10.Steady-state error & PID control
Answer: ess = 10
P, PI and PID control: the controller C(s) = Kp + Ki/s + Kd·s acts on the error. A proportional gain makes the loop faster and reduces the error of a type-0 plant, but never removes it. The integral term adds a pole at s = 0: the system type rises by one, and a step is followed without error. The derivative term adds damping. To choose gains, write the closed-loop characteristic polynomial and compare it with s² + 2ζωns + ωn². Then %OS = 100·e−ζπ/√(1−ζ²), tp = π/ωd with ωd = ωn√(1 − ζ²), and ts ≈ 4/(ζωn).
Velocity constant
s·C(s) = 2s + 2 → 2 as s → 0.
Kv = 2·2/20 = 0.2
Ramp error
ess = 2/0.2 = 10
Answer
ess = 10
The PI controller removes the step error completely; a ramp is followed with a constant lag.
11.Step response
Answer: σ = −1.5
Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).
Compare with the standard form
The denominator must match s² + 2ζωₙs + ωₙ².
ωₙ² = 50 → ωₙ = 7.071 rad/s
2ζωₙ = 3 → ζ = 3/(2·7.071) = 0.2121
Result
σ = −ζωₙ = −3/2 = −1.5
Answer
σ = −1.5
12.Step response
Answer: K = 134.4
Step response: a first-order system G(s) = K/(τs + 1) answers a step of size U with y(t) = K·U·(1 − e−t/τ): it reaches 63.2 % of the final value K·U after one time constant τ and 98 % after 4τ. A second-order system G(s) = K·ωₙ²/(s² + 2ζωₙs + ωₙ²) has the poles s = −ζωₙ ± jωd with ωd = ωₙ√(1 − ζ²). For 0 < ζ < 1 the step response overshoots: percent overshoot %OS = 100·e−ζπ/√(1−ζ²), peak time tp = π/ωd, and the 2 % settling time ts ≈ 4/(ζωₙ). Compare the denominator with s² + 2ζωₙs + ωₙ² to read off ωₙ and ζ. For a mass–spring–damper ωₙ = √(k/m) and ζ = c/(2√(km)); for a series RLC circuit ωₙ = 1/√(LC) and ζ = (R/2)·√(C/L).