Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
How many milligrams of drug m are in 2 mL of a 20% (w/v) solution?
The prescription is 6400 units of a drug that comes as 10000 units/mL. Draw up the dose in the 1 mL syringe: what volume V do you give?
An infusion is ordered at 60 mL/h, but no pump is available. It runs by gravity through a giving set of 60 gtt/mL. Find the drip rate R in drops per minute.
1000 mg of a drug is diluted in 250 mL and given by gravity through a set of 60 gtt/mL. The order is 160 mg per hour. Find the drip rate R in drops per minute.
Practice exercise (made-up values, not clinical guidance). An infusion contains 250 units of regular insulin in 250 mL. The order is 0.1 units/kg/h for a patient who weighs 93 kg. Find the pump rate R in mL/h. Round to one decimal place.
Practice exercise (made-up values, not clinical guidance). A patient who weighs 69 kg has an order for nitroglycerin at 5 mcg/min. The bag contains 50 mg in 250 mL. Find the pump rate R in mL/h. Round to one decimal place.
Practice exercise (made-up values, not clinical guidance). The record shows a patient's intake and output for one 8-hour shift. The patient weighs 98 kg. Find the average urine output U in mL/kg/h. Round to two decimal places.
Practice exercise (made-up values, not clinical guidance). A 500 mL bag was started at 08:30 and runs by pump at 150 mL/h. How many mL V are left in the bag at 11:30?
Practice exercise (made-up values, not clinical guidance). A dose calculation for an injection gives 5.4115 mL. The rule in this exercise is that volumes of 1 mL or more are rounded to the nearest tenth of a mL. What value x do you record?
Practice exercise (made-up values, not clinical guidance). A maintenance infusion runs at 120 mL/h without a break. How many litres V does it deliver in 24 hours?
Answer: m = 400 mg
Solution strengths: a percentage strength is grams per 100 mL, so 1% = 1 g/100 mL = 10 mg/mL. A ratio strength 1:1000 means 1 g in 1000 mL = 1 mg/mL; 1:10 000 is 0.1 mg/mL. For a dilution the amount of drug stays the same: C₁·V₁ = C₂·V₂.
Answer: V = 0.64 mL
Drawing up a dose: volume = (prescribed dose/stock strength) × stock volume. Convert to the same units first, then check that the volume fits the syringe and lands on one of its graduations.
On this 1 mL syringe every small line is 0.01 mL.
Answer: R = 60 gtt/min
Infusion rates: a pump is set in mL/h = volume/time in hours. A gravity drip is counted in drops per minute: gtt/min = volume (mL) × drop factor (gtt/mL)/time (min). The drop factor is printed on the tubing package: macrodrip sets deliver 10, 15 or 20 gtt/mL (blood sets often 10 gtt/mL in the US, 15 in the UK) and microdrip sets 60 gtt/mL. Always use the drop factor the question or package gives.
With a microdrip set (60 gtt/mL), gtt/min equals mL/h.
Answer: R = 40 gtt/min
Dose-based infusions: concentration = amount of drug in the bag/bag volume. Pump rate (mL/h) = dose per hour/concentration, and dose per hour = mL/h × concentration. Convert per-minute doses to per-hour (× 60) and keep the mass units the same (1 g = 1000 mg, 1 mg = 1000 mcg).
Answer: R = 9.3 mL/h
Heparin and insulin infusions: concentration = units in the bag/bag volume (units/mL). Pump rate (mL/h) = units per hour/concentration, and units per hour = mL/h × concentration. For a weight-based order, units/h = units/kg/h × weight first. A bolus volume = units needed/vial strength. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: R = 1.5 mL/h
Titrated drips: first find the concentration in mcg/mL (mg × 1000/mL). For a weight-based order, mcg/min = mcg/kg/min × weight. Then mL/h = mcg/min × 60/concentration. Working backwards, mcg/kg/min = mL/h × concentration/(60 × weight). The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
The order is per minute for the whole patient, so the weight is not needed.
Answer: U = 1.98 mL/kg/h
Intake and output: intake counts everything that goes in (oral fluids, IV infusions, IV medications and flushes, tube feeds); ice chips count as half their volume. Output counts urine, drains, vomit and other losses. Balance = total intake − total output; a negative balance is a net loss. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: V = 50 mL
Infusion time: time (h) = volume to infuse (mL)/rate (mL/h); use the volume still left in the bag, not the bag size. Volume infused = rate × time. Convert decimal hours to hours and minutes with the fraction × 60 (0.5 h = 30 min, not 50 min). The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: x = 5.4 mL
Rounding: look at the digit just after the place you round to: 5 or more rounds up, 4 or less leaves the digit as it is. Round only the final answer, never the steps. Typical exam rules: volumes of 1 mL or more to the nearest tenth, volumes below 1 mL to the nearest hundredth, drip rates to whole drops and weights to one decimal place; always follow the rule the question states.
Answer: V = 2.88 L
Dimensional analysis: write the given quantity, then multiply by conversion factors written as fractions (for example 60 min/1 h or 1 mg/1000 mcg) so that each unwanted unit appears once on top and once underneath and cancels. When only the wanted unit is left, calculate. Use the equivalents the question gives and round only the final answer.
This is independent practice material. ExamProblems is not affiliated with or endorsed by the organisation that runs this exam, and the exam name is used only to describe the content. NCLEX®, NCLEX-RN® and NCLEX-PN® are trademarks of the National Council of State Boards of Nursing, Inc. (NCSBN), which is not affiliated with ExamProblems and does not endorse it or vouch for its accuracy.
ExamProblems · examproblems.com/courses/nclex-dosage-calculations