Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
Practice exercise (made-up values, not clinical guidance). A practice protocol calls for a heparin bolus of 60 units/kg for a patient who weighs 50 kg. The vial contains 5 000 units/mL. What volume V do you draw up? Round to two decimal places.
Practice exercise (made-up values, not clinical guidance). A dopamine infusion of 800 mg in 500 mL runs at 12 mL/h. The patient weighs 52 kg. What dose D in mcg/kg/min is the patient receiving? Round to one decimal place.
A dose of 2000 mg is needed from a 20% (w/v) solution. What volume V contains this dose?
You must prepare 500 mL of a 0.5% (w/v) solution from a 20% (w/v) stock solution. What volume of stock V₁ do you need?
500 mL was ordered over 6 hours. After 3 hours you find that 300 mL is still in the bag, and the order must still finish on time. To what rate R in mL/h must the pump be reset?
1000 mL was ordered over 6 hours. After 2 hours you find that 840 mL is still in the bag, and the order must still finish on time. By what percentage Δ must the original pump rate be increased?
Answer: V = 0.6 mL
Heparin and insulin infusions: concentration = units in the bag/bag volume (units/mL). Pump rate (mL/h) = units per hour/concentration, and units per hour = mL/h × concentration. For a weight-based order, units/h = units/kg/h × weight first. A bolus volume = units needed/vial strength. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: D = 6.2 mcg/kg/min
Titrated drips: first find the concentration in mcg/mL (mg × 1000/mL). For a weight-based order, mcg/min = mcg/kg/min × weight. Then mL/h = mcg/min × 60/concentration. Working backwards, mcg/kg/min = mL/h × concentration/(60 × weight). The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: V = 10 mL
Solution strengths: a percentage strength is grams per 100 mL, so 1% = 1 g/100 mL = 10 mg/mL. A ratio strength 1:1000 means 1 g in 1000 mL = 1 mg/mL; 1:10 000 is 0.1 mg/mL. For a dilution the amount of drug stays the same: C₁·V₁ = C₂·V₂.
Answer: V₁ = 12.5 mL
Solution strengths: a percentage strength is grams per 100 mL, so 1% = 1 g/100 mL = 10 mg/mL. A ratio strength 1:1000 means 1 g in 1000 mL = 1 mg/mL; 1:10 000 is 0.1 mg/mL. For a dilution the amount of drug stays the same: C₁·V₁ = C₂·V₂.
Answer: R = 100 mL/h
Infusion rates: a pump is set in mL/h = volume/time in hours. A gravity drip is counted in drops per minute: gtt/min = volume (mL) × drop factor (gtt/mL)/time (min). The drop factor is printed on the tubing package: macrodrip sets deliver 10, 15 or 20 gtt/mL (blood sets often 10 gtt/mL in the US, 15 in the UK) and microdrip sets 60 gtt/mL. Always use the drop factor the question or package gives.
Many hospitals allow such an adjustment up to 25% without a new order; check local policy.
Answer: Δ = 26 %
Infusion rates: a pump is set in mL/h = volume/time in hours. A gravity drip is counted in drops per minute: gtt/min = volume (mL) × drop factor (gtt/mL)/time (min). The drop factor is printed on the tubing package: macrodrip sets deliver 10, 15 or 20 gtt/mL (blood sets often 10 gtt/mL in the US, 15 in the UK) and microdrip sets 60 gtt/mL. Always use the drop factor the question or package gives.
This is more than a 25% increase: most hospitals require you to contact the prescriber instead of catching up, and to assess the patient for fluid overload.
ExamProblems · examproblems.com/courses/pediatric-and-critical-care-dosing