Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
Practice exercise (made-up values, not clinical guidance). A vial of penicillin G contains 5 000 000 units. Its practice label gives three strengths (see the table). You add 3.2 mL of diluent. The prescribed dose is 2 000 000 units. What volume V do you draw up? Round to one decimal place.
A vial holds 500 mg of powder. You add 3.4 mL of diluent, and the powder adds 0.6 mL of volume. The prescription is 100 mg. Draw up the dose: what volume V do you give?
A child weighing 15 kg is prescribed 3 mg/kg of a drug. The stock solution contains 25 mg/mL. Draw up the dose: what volume V do you give?
The prescription is 510 units of a drug that comes as 1000 units/mL. Draw up the dose in the 1 mL syringe: what volume V do you give?
Practice exercise (made-up values, not clinical guidance). Vancomycin is given as a continuous infusion to a patient whose vancomycin clearance is 70 mL/min. What infusion rate R in mg/h gives a steady-state level of 20 mg/L?
Practice exercise (made-up values, not clinical guidance). A theophylline infusion runs at 42 mg/h with no loading dose. The patient's clearance is 3.5 L/h and the half-life is 6 h. What is the level C after 2 h?
Answer: V = 2 mL
Reconstitution: the powder takes up space, so the final volume is the diluent plus the powder volume. Concentration = drug in the vial/final volume, and the volume to give = dose/concentration. On a multi-strength label, use the concentration that belongs to the amount of diluent you actually added. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: V = 0.8 mL
Strength to volume: turn the strength into mg per mL first. A w/v percentage is grams per 100 mL, so x% = 10x mg/mL. A ratio strength 1:n is 1 g in n mL. After reconstitution the concentration is the powder's dose over the final volume (diluent + powder volume). Then volume = dose/concentration.
Answer: V = 1.8 mL
Drawing up a dose: volume = (prescribed dose/stock strength) × stock volume. Convert to the same units first, then check that the volume fits the syringe and lands on one of its graduations.
On this 10 mL syringe every small line is 0.2 mL.
Answer: V = 0.51 mL
Drawing up a dose: volume = (prescribed dose/stock strength) × stock volume. Convert to the same units first, then check that the volume fits the syringe and lands on one of its graduations.
On this 1 mL syringe every small line is 0.01 mL.
Answer: R = 84 mg/h
Clearance and volume: at steady state the dosing rate equals the elimination rate, so the maintenance rate = CL × Css. A loading dose is LD = Vd × C/(S × F), with S the salt factor (fraction of active drug in the salt) and F the bioavailability (1 for IV). From two levels, k = ln(C₁/C₂)/Δt; for an IV bolus Vd = dose/C₀ and CL = k × Vd. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: C = 2.476 mg/L
Designing a regimen: with rapid IV doses the level falls from peak to trough during the interval, so τ = ln(Cpeak/Ctrough)/k and the dose that restores the peak is Vd × (Cpeak − Ctrough). The average steady-state level is Css,avg = S·F·dose/(CL·τ). An infusion rises as C = (R/CL)(1 − e−kt). For a drug cleared by the kidneys, the dose is scaled with the creatinine clearance. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
ExamProblems · examproblems.com/courses/pharmacy-calculations