Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
Practice exercise (made-up values, not clinical guidance). A vial of penicillin G contains 5 000 000 units. Its practice label gives three strengths (see the table). You add 3.2 mL of diluent. The prescribed dose is 2 000 000 units. What volume V do you draw up? Round to one decimal place.
A vial holds 1000 mg of powder. You add 4.2 mL of diluent, and the powder adds 0.8 mL of volume. The prescription is 420 mg. Draw up the dose: what volume V do you give?
A patient weighs 30 kg and is prescribed 25 mg/kg as a single dose. Find the dose D in mg.
The prescription is 110 micrograms. The ampoule contains 0.5 mg/mL. Draw up the dose in the 1 mL syringe: what volume V do you give?
Practice exercise (made-up values, not clinical guidance). After an IV dose of vancomycin, the level is 25 mg/L at 1 h and 14 mg/L at 6 h. Assume first-order elimination. Find the half-life t½.
Practice exercise (made-up values, not clinical guidance). An 80 kg patient on regular tobramycin doses is at steady state. The target is a peak of 10 mg/L and a trough of 1 mg/L, and the volume of distribution is 0.25 L/kg. Assuming rapid IV doses, what dose D raises the level from the trough to the peak?
Answer: V = 2 mL
Reconstitution: the powder takes up space, so the final volume is the diluent plus the powder volume. Concentration = drug in the vial/final volume, and the volume to give = dose/concentration. On a multi-strength label, use the concentration that belongs to the amount of diluent you actually added. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: V = 2.1 mL
Strength to volume: turn the strength into mg per mL first. A w/v percentage is grams per 100 mL, so x% = 10x mg/mL. A ratio strength 1:n is 1 g in n mL. After reconstitution the concentration is the powder's dose over the final volume (diluent + powder volume). Then volume = dose/concentration.
Answer: D = 750 mg
Dose calculation: the amount to give equals what is prescribed divided by what you have, times the quantity it comes in: amount = (desired dose/stock strength) × stock volume. Always keep the units the same (convert g to mg, mg to mcg first) and check that the answer is sensible.
Answer: V = 0.22 mL
Drawing up a dose: volume = (prescribed dose/stock strength) × stock volume. Convert to the same units first, then check that the volume fits the syringe and lands on one of its graduations.
Answer: t½ = 5.977 h
Clearance and volume: at steady state the dosing rate equals the elimination rate, so the maintenance rate = CL × Css. A loading dose is LD = Vd × C/(S × F), with S the salt factor (fraction of active drug in the salt) and F the bioavailability (1 for IV). From two levels, k = ln(C₁/C₂)/Δt; for an IV bolus Vd = dose/C₀ and CL = k × Vd. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: D = 180 mg
Designing a regimen: with rapid IV doses the level falls from peak to trough during the interval, so τ = ln(Cpeak/Ctrough)/k and the dose that restores the peak is Vd × (Cpeak − Ctrough). The average steady-state level is Css,avg = S·F·dose/(CL·τ). An infusion rises as C = (R/CL)(1 − e−kt). For a drug cleared by the kidneys, the dose is scaled with the creatinine clearance. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
In practice the dose is rounded to a convenient amount.
ExamProblems · examproblems.com/courses/pharmacy-calculations