Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 5 m/s² until it stops. Find the braking distance s.
v₀ = 36 km/ha = −5 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 4 s, then runs at constant speed for 23 s, and finally brakes at 3 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2.5 m/s²t1 = 4 st2 = 23 sa3 = −3 m/s²
s = m
3.Newton’s lawsMedium
A 4 kg block slides down a frictionless slope at 25° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 4 kgθ = 25°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3.5 kgm2 = 3.5 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 22 m/sθ = 45°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 11 m/s and 30° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 11 m/sθ = 30°h = 60 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2.5 kg block slides 17 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 2.5 kgθ = 35°μ = 0.3d = 17 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block rests on a rough horizontal table (μ = 0.25). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 2 kgm2 = 2 kgμ = 0.25d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3 kg glider moving at 7 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 4.5 kgv1 = 7 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 10 m/s and bounces straight back at 4 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 10 m/svout = 4 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 250 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 20 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 1 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A reversible (Carnot) heat engine takes in 1900 kJ of heat from a reservoir at 300 °C and rejects 1022 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 300 °CQH = 1900 kJQL = 1022 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 180 kW of heat from a source at 600 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -25 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 600 °CT0 = 20 °CTL = -25 °CQ̇H = 180 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin converging lens with a focal length of 25 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 50 cmf = 25 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 400 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 400 mm⁻¹λ = 656 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 10 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 10²/(2·5) = 10 m
Answer
s = 10 m
2.Kinematics
Answer: s = 266.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·4 = 10 m/s
Distance of each phase
s1 = ½·2.5·4² = 20 m
s2 = 10·23 = 230 m
s3 = 10²/(2·3) = 16.67 m
Total distance
s = 20 + 230 + 16.67 = 266.7 m
Answer
s = 266.7 m
3.Newton’s laws
Answer: a = 4.146 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 22·cos 45° = 15.56 m/s
vy = v0·sin θ = 22·sin 45° = 15.56 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.56/9.81 = 3.172 s
Horizontal distance
x = vx·t = 15.56·3.172 = 49.34 m
Answer
x = 49.34 m
6.Projectile motion
Answer: H = 61.54 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 11·sin 30° = 5.5 m/s
Rise above the cliff
Δh = vy²/(2g) = 5.5²/(2·9.81) = 1.542 m
Height above the ground
H = 60 + 1.542 = 61.54 m
Answer
H = 61.54 m
7.Work & energy
Answer: Wf = 102.5 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.8192 = 20.09 N
F = μN = 0.3·20.09 = 6.027 N
Work against friction
Wf = F·d = 6.027·17 = 102.5 J
Answer
Wf = 102.5 J
8.Work & energy
Answer: v = 2.712 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·1 = 19.62 J
μ·m₁g·d = 0.25·19.62·1 = 4.905 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 14.71 → v = √(2·14.71/4) = 2.712 m/s
Answer
v = 2.712 m/s
9.Momentum & collisions
Answer: v′2 = 5.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 4.5)/(3 + 4.5)·7 = −1.4 m/s
v′2 = 2·3/(3 + 4.5)·7 = 5.6 m/s
Answer
v′2 = 5.6 m/s
10.Momentum & collisions
Answer: Favg = 192.5 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(4 + 10) = 7.7 N·s
Average force
Favg = J/Δt = 7.7/0.04 = 192.5 N
Answer
Favg = 192.5 N
11.Hydrostatic force
Answer: F = 309 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·9 = 309 kN
Answer
F = 309 kN
12.Hydrostatic force
Answer: ycp = 3.8 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.75·2.25 = 104.3 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 341.3 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 170/28.01 = 6.069 mol
T = 65 + 273.15 = 338.1 K
Pressure
P = nRT/V = 6.069·8.314·338.1/0.05 = 341.3 kPa
Answer
P = 341.3 kPa
16.Ideal gas law
Answer: ρ = 5.57 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 120 + 273.15 = 393.1 K
Density
ρ = 650·28.01/(8.314·393.1) = 5.57 kg/m³
Answer
ρ = 5.57 kg/m³
17.Heat engines & refrigerators
Answer: TL = 35.14 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 300 + 273.15 = 573.1 K
Reversible heat ratio
TL = TH·QL/QH = 573.1·1022/1900 = 308.3 K = 35.14 °C
Answer
TL = 35.14 °C
18.Heat engines & refrigerators
Answer: Q̇L = 659.3 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
T0 = 20 + 273.15 = 293.1 K
TL = -25 + 273.15 = 248.1 K
Engine work
η = 1 − 293.1/873.1 = 0.6643
Ẇ = 0.6643·180 = 119.6 kW
Heat removed by the refrigerator
COPR = 248.1/(293.1 − 248.1) = 5.514
Q̇L = 5.514·119.6 = 659.3 kW
Answer
Q̇L = 659.3 kW
19.Waves, sound & optics
Answer: di = 50 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/25 − 1/50
di = 50 cm
Ray diagram
real, on the far side of the lens
Answer
di = 50 cm
20.Waves, sound & optics
Answer: θ2 = 31.65 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …