Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 6 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −6 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 15 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 15 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 3 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 3 kgθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 5.5 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 5.5 m/sθ = 25°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 30 m/sθ = 45°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 34 m/sθ = 45°h = 35 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1 kg block slides 9 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 1 kgθ = 35°μ = 0.3d = 9 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 10 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.25) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 10 kgh = 1 mL = 1.5 mμ = 0.25k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 7 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3.5 kgm2 = 5 kgv1 = 7 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 1100 kg car travelling east at 13 m/s collides with a 1400 kg car travelling north at 14 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1100 kgv1 = 13 m/s (E)m2 = 1400 kgv2 = 14 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 400 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 75 mm and a gauge pressure of 140 kPa. The nozzle exit diameter is 30 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 2400 kJ of heat from a reservoir at 225 °C and rejects 1557 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 225 °CQH = 2400 kJQL = 1557 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 90 kW of heat from a source at 900 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 900 °CT0 = 30 °CTL = -5 °CQ̇H = 90 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.8 m long. The speed of sound is 343 m/s. Find the frequency f4 of its harmonic number 4.
v = 343 m/sn = 4L = 0.8 m
f4 = Hz
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls at right angles on a grating with 400 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 400 mm⁻¹λ = 589 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 4.167 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/6 = 4.167 s
Answer
t = 4.167 s
2.Kinematics
Answer: t = 4.256 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 15·t − ½·9.81·t²
4.905·t² − 15·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (15 + √(15² + 2·9.81·25))/9.81 = 4.256 s
Answer
t = 4.256 s
3.Newton’s laws
Answer: a = 4.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.1·cos 25°) = 5.035 m/s²
Distance
d = v₀²/(2a) = 5.5²/(2·5.035) = 3.004 m
Answer
d = 3.004 m
5.Projectile motion
Answer: t = 4.325 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 45° = 21.21 m/s
vy = v0·sin θ = 30·sin 45° = 21.21 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·21.21/9.81 = 4.325 s
Answer
t = 4.325 s
6.Projectile motion
Answer: t = 6.076 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 45° = 24.04 m/s
vy = v0·sin θ = 34·sin 45° = 24.04 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 24.04·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (24.04 + √(578 + 686.7))/9.81 = 6.076 s
Answer
t = 6.076 s
7.Work & energy
Answer: Wf = 21.7 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.8192 = 8.036 N
F = μN = 0.3·8.036 = 2.411 N
Work against friction
Wf = F·d = 2.411·9 = 21.7 J
Answer
Wf = 21.7 J
8.Work & energy
Answer: x = 49.52 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(1 − 0.25·1.5) = 61.31 J
Maximum compression
½kx² = 61.31 → x = √(2·61.31/500) = 0.4952 m = 49.52 cm
Answer
x = 49.52 cm
9.Momentum & collisions
Answer: v′1 = −1.235 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 5)/(3.5 + 5)·7 = −1.235 m/s
v′2 = 2·3.5/(3.5 + 5)·7 = 5.765 m/s
Answer
v′1 = −1.235 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v′ = 9.705 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: ycp = 3.25 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3·6 = 181 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·3³/12 = 4.5 m⁴
ycp = yc + Ic/(yc·A) = 3 + 4.5/(3·6) = 3.25 m
Answer
ycp = 3.25 m
13.Continuity & Bernoulli
Answer: p2 = 395.2 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 30/75 = 0.4
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·140000/(1000·0.9744)) = 16.95 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.95²/(2·9.81) = 14.65 m
Answer
H = 14.65 m
15.Ideal gas law
Answer: P = 554 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 230/32 = 7.188 mol
T = 5 + 273.15 = 278.1 K
Pressure
P = nRT/V = 7.188·8.314·278.1/0.03 = 554 kPa
Answer
P = 554 kPa
16.Ideal gas law
Answer: V2 = 6.979 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 423.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(300/600)·(423.1/303.1) = 6.979 L
Answer
V2 = 6.979 L
17.Heat engines & refrigerators
Answer: TL = 50.02 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 225 + 273.15 = 498.1 K
Reversible heat ratio
TL = TH·QL/QH = 498.1·1557/2400 = 323.2 K = 50.02 °C
Answer
TL = 50.02 °C
18.Heat engines & refrigerators
Answer: Q̇L = 511.3 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 900 + 273.15 = 1173 K
T0 = 30 + 273.15 = 303.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 303.1/1173 = 0.7416
Ẇ = 0.7416·90 = 66.74 kW
Heat removed by the refrigerator
COPR = 268.1/(303.1 − 268.1) = 7.661
Q̇L = 7.661·66.74 = 511.3 kW
Answer
Q̇L = 511.3 kW
19.Waves, sound & optics
Answer: f4 = 857.5 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.8/4 = 0.4 m
Frequency
f = v/λ = 343/0.4 = 857.5 Hz
Answer
f4 = 857.5 Hz
20.Waves, sound & optics
Answer: θ1 = 13.63 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …