Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 45 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 19 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 19 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 40 kg box is pushed up a ramp at 20° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the pushing force F.
m = 40 kgθ = 20°μ = 0.4g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 5.5 kgm2 = 5 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 30 m/s and 30° above the horizontal towards a wall 48 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 30 m/sθ = 30°x = 48 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 36 m/s and 30° above the horizontal. It lands on the flat roof of a building 2 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 36 m/sθ = 30°hroof = 2 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 2 m along the slope.
θ = 40°μ = 0.2d = 2 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg cart is released from rest at a height of 4.5 m on a smooth track that leads into a vertical circular loop of radius 1 m. Find the speed v of the cart at the top of the loop.
m = 5 kgh = 4.5 mR = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 12 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 23 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 3 kgh = 23 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 25 m/s and bounces straight back at 8 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.55 kgvin = 25 m/svout = 8 m/sΔt = 40 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a wind tunnel reads a difference of 750 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 750 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 150 mm, throat 75 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 200 mm. The discharge coefficient is 0.96. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 375 °C and a cold reservoir at 30 °C. Find the highest possible thermal efficiency ηmax.
TH = 375 °CTL = 30 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 30 °C, removing heat from the cold space at 4 kW. Find the minimum power input Ẇmin.
TH = 30 °CTL = -18 °CQ̇L = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A small source sends sound equally in all directions. The level is 95 dB at 10 m from it. Find the level β2 at 80 m, ignoring absorption and reflections.
β1 = 95 dBr1 = 10 mr2 = 80 m
β2 = dB
20.Waves, sound & opticsHard
Light of wavelength 650 nm passes through a single slit 0.05 mm wide. Find the angle θ1 of dark fringe number 1 from the straight-through direction.
λ = 650 nma = 0.05 mmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: s = 12.02 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 12.5²/(2·6.5) = 12.02 m
Answer
s = 12.02 m
2.Kinematics
Answer: t = 5.387 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 19·t − ½·9.81·t²
4.905·t² − 19·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (19 + √(19² + 2·9.81·40))/9.81 = 5.387 s
Answer
t = 5.387 s
3.Newton’s laws
Answer: F = 281.7 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 134.2 + 147.5 = 281.7 N
Answer
F = 281.7 N
4.Newton’s laws
Answer: T = 28.26 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 30·cos 30° = 25.98 m/s
t = x/vx = 48/25.98 = 1.848 s
Height at that time
y = 15·1.848 − ½·9.81·1.848² = 10.97 m
Answer
y = 10.97 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 110.8 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 31.18 m/s, vy = 18 m/s
Time to land on the roof
Larger root: the ball is descending.
2 = 18·t − 4.905·t²
t = (18 + √(18² − 2·9.81·2))/9.81 = 3.555 s
Horizontal distance
x = vx·t = 31.18·3.555 = 110.8 m
Answer
x = 110.8 m
7.Work & energy
Answer: v = 4.383 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·2·(0.6428 − 0.2·0.766)) = 4.383 m/s
Answer
v = 4.383 m/s
8.Work & energy
Answer: v = 7.004 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(4.5 − 2) = 49.05 m²/s²
v = 7.004 m/s
Answer
v = 7.004 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 533.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.23) = 2.124 m/s
Collision
m·v = (m + M)·V → v = (0.012 + 3)·2.124/0.012 = 533.2 m/s
Answer
v = 533.2 m/s
10.Momentum & collisions
Answer: J = 18.15 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(8 + 25) = 18.15 N·s
Answer
J = 18.15 N·s
11.Hydrostatic force
Answer: F = 264.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·9 = 264.9 kN
Answer
F = 264.9 kN
12.Hydrostatic force
Answer: ycp = 2.939 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.75·3.75 = 89.03 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·750/1.2) = 35.36 m/s
Answer
v = 35.36 m/s
14.Continuity & Bernoulli
Answer: Q = 30.8 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.2 = 24721 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 375 + 273.15 = 648.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/648.1 = 53.23 %
Answer
ηmax = 53.23 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.7525 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4/5.316 = 0.7525 kW
Answer
Ẇmin = 0.7525 kW
19.Waves, sound & optics
Answer: β2 = 76.94 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity ratio
I₂/I₁ = (10/80)² = 0.01563
New level
β₂ = 95 + 10·log₁₀(0.01563) = 76.94 dB
Answer
β2 = 76.94 dB
Every doubling of the distance lowers the level by about 6 dB.
20.Waves, sound & optics
Answer: θ1 = 0.7449 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …