Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 34 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 34 m/s²t1 = 3 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 25°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 4.5 kgm2 = 3 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 20 m/sθ = 30°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 32 m/s and 40° above the horizontal. It lands on the flat roof of a building 4 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 32 m/sθ = 40°hroof = 4 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 4 kg block slides 19 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.4. Find the work Wf done against friction.
m = 4 kgθ = 35°μ = 0.4d = 19 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.3) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 1.5 mL = 1 mμ = 0.3k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 500 kg car moving at 14 m/s runs into a stationary 600 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 500 kgv1 = 14 m/sm2 = 600 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 1100 kg car runs into a parked 900 kg car. The wrecks lock together and skid 25 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 2.5 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 40 mm. The water level is kept 4.5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 40 mmh = 4.5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 3 m. At section 1 the pressure is 200 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 40 °C. Find the highest possible thermal efficiency ηmax.
TH = 725 °CTL = 40 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 16.5 kW of heat to a heating system at 21 °C, taking heat from a source at -10 °C. Its actual COP is 30% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 21 °CTL = -10 °CηII = 30%Q̇H = 16.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
An object stands 15 cm in front of a thin converging lens with a focal length of 10 cm. Find the magnification m (negative for an inverted image).
do = 15 cmf = 10 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls on two slits 0.3 mm apart. The screen is 1 m away. Find the spacing Δy between neighbouring bright fringes.
λ = 589 nmd = 0.3 mmL = 1 m
Δy = mm
3Solutions
1.Kinematics
Answer: s = 64.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·6) = 64.3 m
Answer
s = 64.3 m
2.Kinematics
Answer: hmax = 683.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 34·3 = 102 m/s
h₁ = ½·34·3² = 153 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 102²/(2·9.81) = 530.3 m
hmax = 153 + 530.3 = 683.3 m
Answer
hmax = 683.3 m
3.Newton’s laws
Answer: a = 2.368 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 30° = 17.32 m/s
vy = v0·sin θ = 20·sin 30° = 10 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·10/9.81 = 2.039 s
Horizontal distance
x = vx·t = 17.32·2.039 = 35.31 m
Answer
x = 35.31 m
6.Projectile motion
Answer: x = 97.79 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 24.51 m/s, vy = 20.57 m/s
Time to land on the roof
Larger root: the ball is descending.
4 = 20.57·t − 4.905·t²
t = (20.57 + √(20.57² − 2·9.81·4))/9.81 = 3.989 s
Horizontal distance
x = vx·t = 24.51·3.989 = 97.79 m
Answer
x = 97.79 m
7.Work & energy
Answer: Wf = 244.3 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.8192 = 32.14 N
F = μN = 0.4·32.14 = 12.86 N
Work against friction
Wf = F·d = 12.86·19 = 244.3 J
Answer
Wf = 244.3 J
8.Work & energy
Answer: x = 4.852 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(1.5 − 0.3·1) = 5.886 J
Maximum compression
½kx² = 5.886 → x = √(2·5.886/5000) = 0.04852 m = 4.852 cm
Answer
x = 4.852 cm
9.Momentum & collisions
Answer: ΔK/K = 54.55 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 500·14/1100 = 6.364 m/s
Kinetic energy before and after
Kbefore = ½·500·14² = 49000 J
Kafter = ½·1100·6.364² = 22273 J
Fraction lost
ΔK/K = 26727/49000 = 54.55 %
Answer
ΔK/K = 54.55 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v1 = 36.02 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4.5) = 9.396 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(100/800)·(383.1/298.1) = 0.8032 L
Answer
V2 = 0.8032 L
17.Heat engines & refrigerators
Answer: ηmax = 68.63 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/998.1 = 68.63 %
Answer
ηmax = 68.63 %
18.Heat engines & refrigerators
Answer: Ẇ = 5.796 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 21 + 273.15 = 294.1 K
TL = -10 + 273.15 = 263.1 K
Carnot and actual COP
COPmax = 294.1/(294.1 − 263.1) = 9.489
COP = 0.3·9.489 = 2.847
Power input
Ẇ = Q̇H/COP = 16.5/2.847 = 5.796 kW
Answer
Ẇ = 5.796 kW
19.Waves, sound & optics
Answer: m = −2
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/10 − 1/15
di = 30 cm
Magnification
m = −di/do = −30/15 = −2
Answer
m = −2
20.Waves, sound & optics
Answer: Δy = 1.963 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …