Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. Find the braking distance s.
v₀ = 36 km/ha = −5.5 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.2 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.2 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
An 8 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 35° with a speed of 5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 5 m/sθ = 35°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 34 m/s and must land 40 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 34 m/sR = 40 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 25° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 21 m/sθ = 25°h = 20 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1500 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 5 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.15 kgk = 1500 N/mx = 5 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 1 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.2) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 1 mL = 2.5 mμ = 0.2k = 800 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 5 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 5 kgm2 = 0.5 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 15 g bullet is fired horizontally into a 5 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 5 kgL = 0.7 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 2 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 270 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 9 m. At section 1 the pressure is 260 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 275 °C and a cold reservoir at 25 °C. Find the highest possible thermal efficiency ηmax.
TH = 275 °CTL = 25 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 32 °C, removing heat from the cold space at 4.5 kW. Find the minimum power input Ẇmin.
TH = 32 °CTL = -25 °CQ̇L = 4.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends must have its harmonic number 3 at 900 Hz; waves travel on it at 240 m/s. Find its length L.
v = 240 m/sn = 3f3 = 900 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 650 nm passes through a single slit 0.12 mm wide. Find the width w of the central bright maximum on a screen 3 m away (between the first dark fringes on either side).
λ = 650 nma = 0.12 mmL = 3 m
w = mm
3Solutions
1.Kinematics
Answer: s = 9.091 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 10²/(2·5.5) = 9.091 m
Answer
s = 9.091 m
2.Kinematics
Answer: d = 77.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.2 − t₁)
4.905·t₁² + 343·t₁ − 1441 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1441))/(2·4.905) = 3.974 s
Depth
d = ½·9.81·3.974² = 77.47 m
Answer
d = 77.47 m
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 35° + 0.15·cos 35°) = 6.832 m/s²
Distance
d = v₀²/(2a) = 5²/(2·6.832) = 1.83 m
Answer
d = 1.83 m
5.Projectile motion
Answer: θ = 9.922 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·40/34² = 0.3394
Angle
2θ = 19.84° → θ = 9.922°
Answer
θ = 9.922°
The other solution is 90° − θ = 80.08°.
6.Projectile motion
Answer: x = 59.33 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 21·cos 25° = 19.03 m/s
vy = v0·sin θ = 21·sin 25° = 8.875 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 8.875·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (8.875 + √(78.77 + 392.4))/9.81 = 3.117 s
Horizontal distance
x = vx·t = 19.03·3.117 = 59.33 m
Answer
x = 59.33 m
7.Work & energy
Answer: h = 1.274 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 5 cm = 0.05 m
½kx² = ½·1500·0.05² = 1.875 J
Height
m·g = 0.15·9.81 = 1.472 N
h = ½kx²/(mg) = 1.875/1.472 = 1.274 m
Answer
h = 1.274 m
8.Work & energy
Answer: x = 11.07 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(1 − 0.2·2.5) = 4.905 J
Maximum compression
½kx² = 4.905 → x = √(2·4.905/800) = 0.1107 m = 11.07 cm
Answer
x = 11.07 cm
9.Momentum & collisions
Answer: v′1 = 9.818 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 0.5)/(5 + 0.5)·12 = 9.818 m/s
v′2 = 2·5/(5 + 0.5)·12 = 21.82 m/s
Answer
v′1 = 9.818 m/s
10.Momentum & collisions
Answer: v = 526.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 35°) = 0.1266 m
Speed after impact
V = √(2·9.81·0.1266) = 1.576 m/s
Collision
v = (m + M)·V/m = 5.015·1.576/0.015 = 526.9 m/s
Answer
v = 526.9 m/s
11.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·3 = 58.86 kN
Answer
F = 58.86 kN
12.Hydrostatic force
Answer: ycp = 5.067 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·5·4 = 172.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 5 + 1.333/(5·4) = 5.067 m
Answer
ycp = 5.067 m
13.Continuity & Bernoulli
Answer: p2 = 180 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 275 + 273.15 = 548.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/548.1 = 45.61 %
Answer
ηmax = 45.61 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.034 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4.5/4.354 = 1.034 kW
Answer
Ẇmin = 1.034 kW
19.Waves, sound & optics
Answer: L = 0.4 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 240/900 = 0.2667 m
Length
L = nλ/2 = 3·0.2667/2 = 0.4 m
Answer
L = 0.4 m
20.Waves, sound & optics
Answer: w = 32.5 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …