Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −3.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 10 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 10 m/sh₀ = 40 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 11.5 m/s and comes to rest after 130 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 11.5 m/sd = 130 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 140 N pulls the front 11 kg block; the 7 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 7 kgm2 = 11 kgF = 140 Nμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 25° above the horizontal and lands 95 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 25°R = 95 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 29 m/s and 65° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 29 m/sθ = 65°h = 40 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 10 kg ball hangs on a light string of length 0.8 m. It is pulled aside until the string makes 40° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 10 kgL = 0.8 mθ = 40°g = 9.81 m/s²
T = N
8.Work & energyHard
A 4 kg block rests on a rough horizontal table (μ = 0.3). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1.5 m.
m1 = 4 kgm2 = 2 kgμ = 0.3d = 1.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 700 kg car moving at 14 m/s runs into a stationary 1800 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 700 kgv1 = 14 m/sm2 = 1800 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.4 kg ball hits a wall at 14 m/s and bounces straight back at 5 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.4 kgvin = 14 m/svout = 5 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a water pipe reads a difference of 38 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 38 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 9 m. At section 1 the pressure is 340 kPa and the velocity is 2.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 500 °C and a cold reservoir at 35 °C. Find the highest possible thermal efficiency ηmax.
TH = 500 °CTL = 35 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 3300 kJ of heat from a reservoir at 900 °C, produces 1254 kJ of work and rejects the rest to a reservoir at 20 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 900 °CTL = 20 °CQH = 3300 kJW = 1254 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin converging lens with a focal length of 15 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 30 cmf = 15 cm
di = cm
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 25 kHz towards a car that approaches at 25 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 25 kHzu = 25 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: s = 27.56 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·3.5) = 27.56 m
Answer
s = 27.56 m
2.Kinematics
Answer: t = 4.052 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−40 = 10·t − ½·9.81·t²
4.905·t² − 10·t − 40 = 0
Solve the quadratic
Only the positive root is physical.
t = (10 + √(10² + 2·9.81·40))/9.81 = 4.052 s
Answer
t = 4.052 s
3.Newton’s laws
Answer: μ = 0.05185
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 11.5²/(2·130) = 0.5087 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.5087/9.81 = 0.05185
Answer
μ = 0.05185
4.Newton’s laws
Answer: T = 54.44 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: v0 = 34.88 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·95/sin 50°) = 34.88 m/s
Answer
v0 = 34.88 m/s
6.Projectile motion
Answer: H = 75.21 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 29·sin 65° = 26.28 m/s
Rise above the cliff
Δh = vy²/(2g) = 26.28²/(2·9.81) = 35.21 m
Height above the ground
H = 40 + 35.21 = 75.21 m
Answer
H = 75.21 m
7.Work & energy
Answer: T = 144 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·0.8·(1 − cos 40°) = 3.672 m²/s²
Forces at the bottom
m·g = 10·9.81 = 98.1 N
T = mg + mv²/L = 98.1 + 10·3.672/0.8 = 144 N
Answer
T = 144 N
Check: T = mg(3 − 2cos θ) = 144 N.
8.Work & energy
Answer: v = 1.981 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·1.5 = 29.43 J
μ·m₁g·d = 0.3·39.24·1.5 = 17.66 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 11.77 → v = √(2·11.77/6) = 1.981 m/s
Answer
v = 1.981 m/s
9.Momentum & collisions
Answer: ΔK = 49392 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 700·14/2500 = 3.92 m/s
Kinetic energy before and after
Kbefore = ½·700·14² = 68600 J
Kafter = ½·2500·3.92² = 19208 J
Energy lost
ΔK = 68600 − 19208 = 49392 J
Answer
ΔK = 49392 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 190 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.4·(5 + 14) = 7.6 N·s
Average force
Favg = J/Δt = 7.6/0.04 = 190 N
Answer
Favg = 190 N
11.Hydrostatic force
Answer: F = 44.15 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·1 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: ycp = 3.308 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.25·1.5 = 42.08 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·38000/1000) = 8.718 m/s
Answer
v = 8.718 m/s
14.Continuity & Bernoulli
Answer: p2 = 204.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/773.1 = 60.14 %
Answer
ηmax = 60.14 %
18.Heat engines & refrigerators
Answer: Sgen = 4.166 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 3300 − 1254 = 2046 kJ
Absolute temperatures
TH = 900 + 273.15 = 1173 K
TL = 20 + 273.15 = 293.1 K
Entropy changes of the reservoirs
ΔSH = −3300/1173 = −2.813 kJ/K
ΔSL = 2046/293.1 = 6.979 kJ/K
Sgen = 6.979 − 2.813 = 4.166 kJ/K
Answer
Sgen = 4.166 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: di = 30 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/30
di = 30 cm
Ray diagram
real, on the far side of the lens
Answer
di = 30 cm
20.Waves, sound & optics
Answer: f″ = 28931 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.