Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 25 m. At the same instant ball B is thrown straight up from the ground directly below at 22 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 25 mv0B = 22 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 14 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 14 kgθ = 40°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 11.5 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 11.5 m/sθ = 30°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 36 m/sθ = 35°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 37 m/s and 35° above the horizontal. It lands on the flat roof of a building 11 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 37 m/sθ = 35°hroof = 11 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 200 N/m. A 0.5 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.5 kgk = 200 N/mx = 10 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A spring of stiffness 5000 N/m at the bottom of a 35° slope is compressed by 12 cm against a 3 kg block and released. The coefficient of kinetic friction between block and slope is 0.25. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1400 kg car moving at 5 m/s runs into a stationary 2000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1400 kgv1 = 5 m/sm2 = 2000 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 25 m/s and bounces straight back at 8 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.3 kgvin = 25 m/svout = 8 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 100 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 5 m. At section 1 the pressure is 120 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 325 °C and a cold reservoir at 35 °C. It takes in 3200 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 325 °CTL = 35 °CQH = 3200 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -10 °C in a kitchen at 25 °C, removing heat from the cold space at 2.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = -10 °CQ̇L = 2.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin diverging lens with a focal length of 5 cm. Find the magnification m (negative for an inverted image).
do = 30 cmf = −5 cm
m =
20.Waves, sound & opticsHard
Two slits 0.3 mm apart are lit with monochromatic light. On a screen 2 m away, bright fringe number 1 lies 3.547 mm from the central fringe. Find the wavelength λ.
d = 0.3 mmL = 2 my1 = 3.547 mmm = 1
λ = nm
3Solutions
1.Kinematics
Answer: s = 21.43 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·4.5) = 21.43 m
Answer
s = 21.43 m
2.Kinematics
Answer: y = 18.67 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
25 − ½g·t² = 22·t − ½g·t² → t = 25/22 = 1.136 s
Meeting height
y = 22·1.136 − ½·9.81·1.136² = 18.67 m
Answer
y = 18.67 m
3.Newton’s laws
Answer: a = 4.803 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.2·cos 30°) = 6.604 m/s²
Distance
d = v₀²/(2a) = 11.5²/(2·6.604) = 10.01 m
Answer
d = 10.01 m
5.Projectile motion
Answer: x = 124.1 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 36·cos 35° = 29.49 m/s
vy = v0·sin θ = 36·sin 35° = 20.65 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·20.65/9.81 = 4.21 s
Horizontal distance
x = vx·t = 29.49·4.21 = 124.1 m
Answer
x = 124.1 m
6.Projectile motion
Answer: x = 112.9 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 30.31 m/s, vy = 21.22 m/s
Time to land on the roof
Larger root: the ball is descending.
11 = 21.22·t − 4.905·t²
t = (21.22 + √(21.22² − 2·9.81·11))/9.81 = 3.725 s
Horizontal distance
x = vx·t = 30.31·3.725 = 112.9 m
Answer
x = 112.9 m
7.Work & energy
Answer: h = 0.2039 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·200·0.1² = 1 J
Height
m·g = 0.5·9.81 = 4.905 N
h = ½kx²/(mg) = 1/4.905 = 0.2039 m
Answer
h = 0.2039 m
8.Work & energy
Answer: d = 1.572 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·5000·0.12² = 36 J
Energy balance along the slope
m·g = 3·9.81 = 29.43 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 36/(29.43·(0.5736 + 0.25·0.8192)) = 1.572 m
Answer
d = 1.572 m
9.Momentum & collisions
Answer: ΔK = 10294 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1400·5/3400 = 2.059 m/s
Kinetic energy before and after
Kbefore = ½·1400·5² = 17500 J
Kafter = ½·3400·2.059² = 7206 J
Energy lost
ΔK = 17500 − 7206 = 10294 J
Answer
ΔK = 10294 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 495 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(8 + 25) = 9.9 N·s
Average force
Favg = J/Δt = 9.9/0.02 = 495 N
Answer
Favg = 495 N
11.Hydrostatic force
Answer: F = 176.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·6 = 176.6 kN
Answer
F = 176.6 kN
12.Hydrostatic force
Answer: F = 15.08 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1·1.5 = 15.08 kN
Answer
F = 15.08 kN
13.Continuity & Bernoulli
Answer: p2 = 98.92 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 363.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(400/800)·(363.1/303.1) = 5.99 L
Answer
V2 = 5.99 L
17.Heat engines & refrigerators
Answer: Wmax = 1551 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 325 + 273.15 = 598.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/598.1 = 48.48 %
Maximum work
Wmax = ηmax·QH = 0.4848·3200 = 1551 kJ
Answer
Wmax = 1551 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3325 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 2.5/7.519 = 0.3325 kW
Answer
Ẇmin = 0.3325 kW
19.Waves, sound & optics
Answer: m = 0.1429
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−5) − 1/30
di = −4.286 cm
Magnification
m = −di/do = −(−4.286)/30 = 0.1429
Answer
m = 0.1429
20.Waves, sound & optics
Answer: λ = 532.1 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …