Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 15 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 2.5 m/s². How long does it take the police car to catch up? Find t.
vcar = 15 m/sapolice = 2.5 m/s²v0,police = 0
t = s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 1.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 32 m/s²t1 = 1.5 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 20° above the horizontal with a force of 190 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 190 Nθ = 20°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 6 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4 kgm2 = 6 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 18 m/sθ = 40°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 12 m/sθ = 55°h = 15 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 10 kg block slides 7 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 10 kgθ = 20°μ = 0.2d = 7 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 10 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.15) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 10 kgh = 3 mL = 5 mμ = 0.15k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 12 g bullet is fired horizontally into a 4 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 6 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 4 kgh = 6 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 26 m/s and bounces straight back at 6 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 26 m/svout = 6 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 250 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 370 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 5 °C. It takes in 600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 650 °CTL = 5 °CQH = 600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 2 °C outside, delivering 9 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 2 °CQ̇H = 9 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 1 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 450 nm passes through a single slit 0.2 mm wide. Find the width w of the central bright maximum on a screen 1 m away (between the first dark fringes on either side).
λ = 450 nma = 0.2 mmL = 1 m
w = mm
3Solutions
1.Kinematics
Answer: t = 12 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·15/2.5 = 12 s
Answer
t = 12 s
At that moment the police car moves at 2v = 30 m/s.
2.Kinematics
Answer: hmax = 153.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·1.5 = 48 m/s
h₁ = ½·32·1.5² = 36 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 48²/(2·9.81) = 117.4 m
hmax = 36 + 117.4 = 153.4 m
Answer
hmax = 153.4 m
3.Newton’s laws
Answer: a = 5.339 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 190·sin 20° = 180.3 N
Horizontal forces
m·a = F·cos θ − μ·N = 178.5 − 45.07
a = 133.5/25 = 5.339 m/s²
Answer
a = 5.339 m/s²
4.Newton’s laws
Answer: T = 25.9 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 40° = 13.79 m/s
vy = v0·sin θ = 18·sin 40° = 11.57 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 11.57²/(2·9.81) = 6.823 m
Answer
H = 6.823 m
6.Projectile motion
Answer: t = 3.017 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 55° = 6.883 m/s
vy = v0·sin θ = 12·sin 55° = 9.83 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 9.83·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.83 + √(96.63 + 294.3))/9.81 = 3.017 s
Answer
t = 3.017 s
7.Work & energy
Answer: Wf = 129.1 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.9397 = 92.18 N
F = μN = 0.2·92.18 = 18.44 N
Work against friction
Wf = F·d = 18.44·7 = 129.1 J
Answer
Wf = 129.1 J
8.Work & energy
Answer: x = 54.25 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(3 − 0.15·5) = 220.7 J
Maximum compression
½kx² = 220.7 → x = √(2·220.7/1500) = 0.5425 m = 54.25 cm
Answer
x = 54.25 cm
9.Momentum & collisions
Answer: v = 362.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.06) = 1.085 m/s
Collision
m·v = (m + M)·V → v = (0.012 + 4)·1.085/0.012 = 362.7 m/s
Answer
v = 362.7 m/s
10.Momentum & collisions
Answer: Favg = 1600 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(6 + 26) = 16 N·s
Average force
Favg = J/Δt = 16/0.01 = 1600 N
Answer
Favg = 1600 N
11.Hydrostatic force
Answer: F = 198.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·4.5 = 198.7 kN
Answer
F = 198.7 kN
12.Hydrostatic force
Answer: F = 28.28 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.25·2.25 = 28.28 kN
Answer
F = 28.28 kN
13.Continuity & Bernoulli
Answer: p2 = 240.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.37 = 45734 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/923.1 = 69.87 %
Maximum work
Wmax = ηmax·QH = 0.6987·600 = 419.2 kJ
Answer
Wmax = 419.2 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5526 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 9/16.29 = 0.5526 kW
Answer
Ẇmin = 0.5526 kW
19.Waves, sound & optics
Answer: f5 = 428.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1/5 = 0.8 m
Frequency
f = v/λ = 343/0.8 = 428.8 Hz
Answer
f5 = 428.8 Hz
20.Waves, sound & optics
Answer: w = 4.5 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …