Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 15 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 4.5 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 15 m/sapolice = 4.5 m/s²v0,police = 0
d = m
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 8 s, then runs at constant speed for 19 s, and finally brakes at 5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2.5 m/s²t1 = 8 st2 = 19 sa3 = −5 m/s²
s = m
3.Newton’s lawsMedium
Masses of 8 kg and 7 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 8 kgm2 = 7 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1.5 kgm2 = 5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 50° above the horizontal towards a wall 48 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 50°x = 48 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 50 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 35 m/sθ = 35°h = 50 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 14 m along the slope.
θ = 35°μ = 0.35d = 14 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 5000 N/m at the bottom of a 25° slope is compressed by 10 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1 kgm2 = 0.5 kgv1 = 3 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 15 g bullet is fired horizontally into a 2.5 kg block hanging from light strings 0.8 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 2.5 kgL = 0.8 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 2.5 mH = 1 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
A pitot-static tube in a wind tunnel reads a difference of 1300 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 1300 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 10 m. At section 1 the pressure is 230 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 800 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 800 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 32 °C, removing heat from the cold space at 4 kW. Find the minimum power input Ẇmin.
TH = 32 °CTL = 5 °CQ̇L = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 20 cm in front of a thin diverging lens with a focal length of 5 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 20 cmf = −5 cm
di = cm
20.Waves, sound & opticsHard
An object is 40 cm in front of a concave mirror with a radius of curvature of 60 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 40 cmR = 60 cm
di = cm
3Solutions
1.Kinematics
Answer: d = 100 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·15/4.5 = 6.667 s
Distance
d = v·t = 15·6.667 = 100 m
Answer
d = 100 m
At that moment the police car moves at 2v = 30 m/s.
2.Kinematics
Answer: s = 500 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·8 = 20 m/s
Distance of each phase
s1 = ½·2.5·8² = 80 m
s2 = 20·19 = 380 m
s3 = 20²/(2·5) = 40 m
Total distance
s = 80 + 380 + 40 = 500 m
Answer
s = 500 m
3.Newton’s laws
Answer: a = 0.654 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (8 − 7)·9.81/(8 + 7) = 0.654 m/s²
Answer
a = 0.654 m/s²
4.Newton’s laws
Answer: a = 6.98 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 50° = 25.71 m/s
t = x/vx = 48/25.71 = 1.867 s
Height at that time
y = 30.64·1.867 − ½·9.81·1.867² = 40.11 m
Answer
y = 40.11 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 167.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 35° = 28.67 m/s
vy = v0·sin θ = 35·sin 35° = 20.08 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 50 + 20.08·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (20.08 + √(403 + 981))/9.81 = 5.839 s
Horizontal distance
x = vx·t = 28.67·5.839 = 167.4 m
Answer
x = 167.4 m
7.Work & energy
Answer: v = 8.877 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·14·(0.5736 − 0.35·0.8192)) = 8.877 m/s
Answer
v = 8.877 m/s
8.Work & energy
Answer: d = 0.844 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·5000·0.1² = 25 J
Energy balance along the slope
m·g = 5·9.81 = 49.05 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 25/(49.05·(0.4226 + 0.2·0.9063)) = 0.844 m
Answer
d = 0.844 m
9.Momentum & collisions
Answer: v′1 = 1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1 − 0.5)/(1 + 0.5)·3 = 1 m/s
v′2 = 2·1/(1 + 0.5)·3 = 4 m/s
Answer
v′1 = 1 m/s
10.Momentum & collisions
Answer: v = 122.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.8·(1 − cos 15°) = 0.02726 m
Speed after impact
V = √(2·9.81·0.02726) = 0.7313 m/s
Collision
v = (m + M)·V/m = 2.515·0.7313/0.015 = 122.6 m/s
Answer
v = 122.6 m/s
11.Hydrostatic force
Answer: F = 60.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·2.25 = 60.7 kN
Answer
F = 60.7 kN
12.Hydrostatic force
Answer: ycp = 3.028 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3·3 = 77.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 3·1³/12 = 0.25 m⁴
ycp = yc + Ic/(yc·A) = 3 + 0.25/(3·3) = 3.028 m
Answer
ycp = 3.028 m
13.Continuity & Bernoulli
Answer: v = 46.55 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·1300/1.2) = 46.55 m/s
Answer
v = 46.55 m/s
14.Continuity & Bernoulli
Answer: p2 = 128.6 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/1073 = 74.08 %
Answer
ηmax = 74.08 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3883 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4/10.3 = 0.3883 kW
Answer
Ẇmin = 0.3883 kW
19.Waves, sound & optics
Answer: di = −4 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−5) − 1/20
di = −4 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −4 cm
20.Waves, sound & optics
Answer: di = 120 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.