Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 14 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 14 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 2.5 m/s and comes to rest after 2.1 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 2.5 m/sd = 2.1 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1 kgm2 = 3 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 20 m/s and must land 35 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 20 m/sR = 35 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 14 m/s and 20° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 14 m/sθ = 20°h = 55 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 5 kg block slides 9 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 5 kgθ = 30°μ = 0.15d = 9 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.15) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 3.5 mL = 4 mμ = 0.15k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 16 kg projectile moving horizontally at 38 m/s explodes into two fragments that move along the same line. The 2 kg fragment continues forwards at 55 m/s. Find the velocity v′2 of the 14 kg fragment (positive in the original direction).
M = 16 kgu = 38 m/sm1 = 2 kgv′1 = 55 m/sm2 = 14 kg
v′2 = m/s
10.Momentum & collisionsHard
A 1500 kg car runs into a parked 2000 kg car. The wrecks lock together and skid 23 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 150 mm to 100 mm. In the wide section the pressure is 180 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 100 kPa. Water leaves through an opening with a diameter of 40 mm, 5 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A reversible refrigerator keeps a cold room at -10 °C by removing 7.5 kW of heat, and rejects heat to the surroundings at 20 °C. Find the rate Q̇H at which it rejects heat.
TL = -10 °CTH = 20 °CQ̇L = 7.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 2 °C outside, delivering 7 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 2 °CQ̇H = 7 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object 2 cm tall stands 40 cm in front of a thin converging lens with a focal length of 30 cm. Find the image height hi (negative for an inverted image).
ho = 2 cmdo = 40 cmf = 30 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 633 nm falls at right angles on a grating with 1200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 1200 mm⁻¹λ = 633 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: s = 14.84 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·6.5) = 14.84 m
Answer
s = 14.84 m
2.Kinematics
Answer: t = 4.456 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 14·t − ½·9.81·t²
4.905·t² − 14·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (14 + √(14² + 2·9.81·35))/9.81 = 4.456 s
Answer
t = 4.456 s
3.Newton’s laws
Answer: μ = 0.1517
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 2.5²/(2·2.1) = 1.488 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.488/9.81 = 0.1517
Answer
μ = 0.1517
4.Newton’s laws
Answer: a = 7.357 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·35/20² = 0.8584
Angle
2θ = 59.13° → θ = 29.57°
Answer
θ = 29.57°
The other solution is 90° − θ = 60.43°.
6.Projectile motion
Answer: H = 56.17 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 14·sin 20° = 4.788 m/s
Rise above the cliff
Δh = vy²/(2g) = 4.788²/(2·9.81) = 1.169 m
Height above the ground
H = 55 + 1.169 = 56.17 m
Answer
H = 56.17 m
7.Work & energy
Answer: Wf = 57.35 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.866 = 42.48 N
F = μN = 0.15·42.48 = 6.372 N
Work against friction
Wf = F·d = 6.372·9 = 57.35 J
Answer
Wf = 57.35 J
8.Work & energy
Answer: x = 16.87 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3.5 − 0.15·4) = 14.22 J
Maximum compression
½kx² = 14.22 → x = √(2·14.22/1000) = 0.1687 m = 16.87 cm
Answer
x = 16.87 cm
9.Momentum & collisions
Answer: v′2 = 35.57 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 16·38 = 608 kg·m/s
Momentum after
608 = 2·55 + 14·v′2
v′2 = (608 − 110)/14 = 35.57 m/s
Answer
v′2 = 35.57 m/s
10.Momentum & collisions
Answer: v1 = 44.33 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(100000/1000 + 9.81·5)) = 17.27 m/s
Flow rate
Q = A·v = 0.001257·17.27 = 0.0217 m³/s = 21.7 L/s
Answer
Q = 21.7 L/s
15.Ideal gas law
Answer: P = 1839 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 350/44.01 = 7.953 mol
T = 5 + 273.15 = 278.1 K
Pressure
P = nRT/V = 7.953·8.314·278.1/0.01 = 1839 kPa
Answer
P = 1839 kPa
16.Ideal gas law
Answer: ρ = 8.126 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 20 + 273.15 = 293.1 K
Density
ρ = 450·44.01/(8.314·293.1) = 8.126 kg/m³
Answer
ρ = 8.126 kg/m³
17.Heat engines & refrigerators
Answer: Q̇H = 8.355 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 20 + 273.15 = 293.1 K
TL = -10 + 273.15 = 263.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 7.5·293.1/263.1 = 8.355 kW
Answer
Q̇H = 8.355 kW
Power input: Ẇ = 0.855 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4298 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 7/16.29 = 0.4298 kW
Answer
Ẇmin = 0.4298 kW
19.Waves, sound & optics
Answer: hi = −6 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/40
di = 120 cm
Magnification and height
m = −120/40 = −3
hi = −3·2 = −6 cm
Answer
hi = −6 cm
20.Waves, sound & optics
Answer: θ1 = 49.43 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …