Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −4 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 2 m/s² for 8 s, then runs at constant speed for 30 s, and finally brakes at 5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2 m/s²t1 = 8 st2 = 30 sa3 = −5 m/s²
s = m
3.Newton’s lawsMedium
A 4 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 4 kgθ = 30°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 2.5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 30 m/sθ = 55°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 34 m/s and 65° above the horizontal. It lands on the flat roof of a building 8 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 34 m/sθ = 65°hroof = 8 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 10 kg block slides 11 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 10 kgθ = 25°μ = 0.35d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.15) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 3.5 mL = 3 mμ = 0.15k = 2500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 4 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 4 kgm2 = 2 kgv1 = 8 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 1300 kg car runs into a parked 1600 kg car. The wrecks lock together and skid 5.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.6. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 230 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 3 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 40 mmzC = +2.5 mz2 = −3 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 280 g of CH₄ occupy at 100 kPa and 65 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 750 °C and a cold reservoir at 25 °C. It takes in 1300 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 750 °CTL = 25 °CQH = 1300 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 180 kW of heat from a source at 850 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -30 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 850 °CT0 = 20 °CTL = -30 °CQ̇H = 180 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 20 cm in front of a thin converging lens with a focal length of 8 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 20 cmf = 8 cm
di = cm
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.48 and a cladding with n₂ = 1.45. Find its numerical aperture NA.
n1 = 1.48n2 = 1.45
NA =
3Solutions
1.Kinematics
Answer: s = 24.11 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·4) = 24.11 m
Answer
s = 24.11 m
2.Kinematics
Answer: s = 569.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2·8 = 16 m/s
Distance of each phase
s1 = ½·2·8² = 64 m
s2 = 16·30 = 480 m
s3 = 16²/(2·5) = 25.6 m
Total distance
s = 64 + 480 + 25.6 = 569.6 m
Answer
s = 569.6 m
3.Newton’s laws
Answer: a = 2.781 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 55° = 17.21 m/s
vy = v0·sin θ = 30·sin 55° = 24.57 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·24.57/9.81 = 5.01 s
Answer
t = 5.01 s
6.Projectile motion
Answer: x = 86.37 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 14.37 m/s, vy = 30.81 m/s
Time to land on the roof
Larger root: the ball is descending.
8 = 30.81·t − 4.905·t²
t = (30.81 + √(30.81² − 2·9.81·8))/9.81 = 6.011 s
Horizontal distance
x = vx·t = 14.37·6.011 = 86.37 m
Answer
x = 86.37 m
7.Work & energy
Answer: Wf = 342.3 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.9063 = 88.91 N
F = μN = 0.35·88.91 = 31.12 N
Work against friction
Wf = F·d = 31.12·11 = 342.3 J
Answer
Wf = 342.3 J
8.Work & energy
Answer: x = 34.6 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(3.5 − 0.15·3) = 149.6 J
Maximum compression
½kx² = 149.6 → x = √(2·149.6/2500) = 0.346 m = 34.6 cm
Answer
x = 34.6 cm
9.Momentum & collisions
Answer: v′1 = 2.667 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 2)/(4 + 2)·8 = 2.667 m/s
v′2 = 2·4/(4 + 2)·8 = 10.67 m/s
Answer
v′1 = 2.667 m/s
10.Momentum & collisions
Answer: v1 = 17.95 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·1.5 = 55.18 kN
Answer
F = 55.18 kN
12.Hydrostatic force
Answer: F = 123.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.5·4 = 123.6 kN
Answer
F = 123.6 kN
13.Continuity & Bernoulli
Answer: p2 = 207.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(300/550)·(523.1/293.1) = 1.947 L
Answer
V2 = 1.947 L
17.Heat engines & refrigerators
Answer: Wmax = 921.2 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/1023 = 70.86 %
Maximum work
Wmax = ηmax·QH = 0.7086·1300 = 921.2 kJ
Answer
Wmax = 921.2 kJ
18.Heat engines & refrigerators
Answer: Q̇L = 646.9 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 850 + 273.15 = 1123 K
T0 = 20 + 273.15 = 293.1 K
TL = -30 + 273.15 = 243.1 K
Engine work
η = 1 − 293.1/1123 = 0.739
Ẇ = 0.739·180 = 133 kW
Heat removed by the refrigerator
COPR = 243.1/(293.1 − 243.1) = 4.863
Q̇L = 4.863·133 = 646.9 kW
Answer
Q̇L = 646.9 kW
19.Waves, sound & optics
Answer: di = 13.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/20
di = 13.33 cm
Ray diagram
real, on the far side of the lens
Answer
di = 13.33 cm
20.Waves, sound & optics
Answer: NA = 0.2965
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.