Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −7.5 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 4 s, then runs at constant speed for 5 s, and finally brakes at 4 m/s² until it stops. Find the total distance s between the two stops.
a1 = 3 m/s²t1 = 4 st2 = 5 sa3 = −4 m/s²
s = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 100 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 100 Nθ = 35°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 120 N pulls the front 2 kg block; the 7 kg block is towed behind. The coefficient of kinetic friction is 0.2 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 7 kgm2 = 2 kgF = 120 Nμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 60°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 17 m/s and 70° above the horizontal. It lands on the flat roof of a building 5 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 17 m/sθ = 70°hroof = 5 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1500 N/m. A 0.2 kg ball is placed on it and the spring is compressed by 5 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.2 kgk = 1500 N/mx = 5 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 15 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 155 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 4 m up the slope.
A 20 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 11 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 2.5 kgh = 11 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.1 kg ball hits a wall at 9 m/s and bounces straight back at 12 m/s. The contact lasts 5 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.1 kgvin = 9 m/svout = 12 m/sΔt = 5 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 54 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 7 m. At section 1 the pressure is 170 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 1300 kJ of heat from a reservoir at 475 °C and rejects 475 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 475 °CQH = 1300 kJQL = 475 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 0 °C outside, delivering 4 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 0 °CQ̇H = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A source of 500 Hz moving at 34 m/s and an observer moving at 10 m/s move away from each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 500 Hzv = 343 m/svs = 34 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls on two slits 0.3 mm apart. The screen is 2.5 m away. Find the spacing Δy between neighbouring bright fringes.
λ = 600 nmd = 0.3 mmL = 2.5 m
Δy = mm
3Solutions
1.Kinematics
Answer: t = 3.704 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/7.5 = 3.704 s
Answer
t = 3.704 s
2.Kinematics
Answer: s = 102 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·4 = 12 m/s
Distance of each phase
s1 = ½·3·4² = 24 m
s2 = 12·5 = 60 m
s3 = 12²/(2·4) = 18 m
Total distance
s = 24 + 60 + 18 = 102 m
Answer
s = 102 m
3.Newton’s laws
Answer: a = 2.36 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 100·sin 35° = 138.8 N
Horizontal forces
m·a = F·cos θ − μ·N = 81.92 − 34.71
a = 47.2/20 = 2.36 m/s²
Answer
a = 2.36 m/s²
4.Newton’s laws
Answer: T = 93.33 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: t = 4.237 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 60° = 12 m/s
vy = v0·sin θ = 24·sin 60° = 20.78 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·20.78/9.81 = 4.237 s
Answer
t = 4.237 s
6.Projectile motion
Answer: x = 16.9 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 5.814 m/s, vy = 15.97 m/s
Time to land on the roof
Larger root: the ball is descending.
5 = 15.97·t − 4.905·t²
t = (15.97 + √(15.97² − 2·9.81·5))/9.81 = 2.906 s
Horizontal distance
x = vx·t = 5.814·2.906 = 16.9 m
Answer
x = 16.9 m
7.Work & energy
Answer: h = 0.9557 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 5 cm = 0.05 m
½kx² = ½·1500·0.05² = 1.875 J
Height
m·g = 0.2·9.81 = 1.962 N
h = ½kx²/(mg) = 1.875/1.962 = 0.9557 m
Answer
h = 0.9557 m
8.Work & energy
Answer: v = 5.588 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 15·9.81 = 147.2 N
mg·sin θ = 84.4 N
μ·mg·cos θ = 12.05 N
Work–energy
½mv² = (155 − 96.46)·4 = 234.2 J
v = √(2·234.2/15) = 5.588 m/s
Answer
v = 5.588 m/s
9.Momentum & collisions
Answer: v = 185.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.11) = 1.469 m/s
Collision
m·v = (m + M)·V → v = (0.02 + 2.5)·1.469/0.02 = 185.1 m/s
Answer
v = 185.1 m/s
10.Momentum & collisions
Answer: J = 2.1 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.1·(12 + 9) = 2.1 N·s
Answer
J = 2.1 N·s
11.Hydrostatic force
Answer: F = 128.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·2.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: F = 127.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.75·3.75 = 127.5 kN
Answer
F = 127.5 kN
13.Continuity & Bernoulli
Answer: Q = 189.7 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 475 + 273.15 = 748.1 K
Reversible heat ratio
TL = TH·QL/QH = 748.1·475/1300 = 273.4 K = 0.2125 °C
Answer
TL = 0.2125 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.2982 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 4/13.42 = 0.2982 kW
Answer
Ẇmin = 0.2982 kW
19.Waves, sound & optics
Answer: f′ = 441.6 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …