Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 4 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −4 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 2.3 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 2.3 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 20 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 20 kgθ = 35°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 75 N pulls the front 10 kg block; the 9 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 9 kgm2 = 10 kgF = 75 Nμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 75° above the horizontal and lands 145 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 75°R = 145 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 25 m/s and 70° above the horizontal from the top of a 25 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 25 m/sθ = 70°h = 25 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 200 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.15 kgk = 200 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 4 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 2.5 mL = 2 mμ = 0.1k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1800 kg car moving at 25 m/s runs into a stationary 1700 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1800 kgv1 = 25 m/sm2 = 1700 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 5 kg block hanging from light strings 1.1 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 5 kgL = 1.1 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows at 33 L/s through a horizontal pipe that narrows from 150 mm to 100 mm. The pressure in the narrow section is 240 kPa. Ignoring losses, find the pressure p1 in the wide section.
A closed water tank has compressed air above the water at a gauge pressure of 170 kPa. Water leaves through an opening with a diameter of 20 mm, 4 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 475 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 475 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 750 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines produce the same work. Find Tm in °C.
TH = 750 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends must have its harmonic number 5 at 500 Hz; waves travel on it at 300 m/s. Find its length L.
v = 300 m/sn = 5f5 = 500 Hz
L = m
20.Waves, sound & opticsHard
An object is 20 cm in front of a concave mirror with a radius of curvature of 30 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 20 cmR = 30 cm
di = cm
3Solutions
1.Kinematics
Answer: s = 78.13 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·4) = 78.13 m
Answer
s = 78.13 m
2.Kinematics
Answer: d = 24.37 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(2.3 − t₁)
4.905·t₁² + 343·t₁ − 788.9 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·788.9))/(2·4.905) = 2.229 s
Depth
d = ½·9.81·2.229² = 24.37 m
Answer
d = 24.37 m
3.Newton’s laws
Answer: a = 4.421 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: v0 = 53.34 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·145/sin 150°) = 53.34 m/s
Answer
v0 = 53.34 m/s
6.Projectile motion
Answer: H = 53.13 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 25·sin 70° = 23.49 m/s
Rise above the cliff
Δh = vy²/(2g) = 23.49²/(2·9.81) = 28.13 m
Height above the ground
H = 25 + 28.13 = 53.13 m
Answer
H = 53.13 m
7.Work & energy
Answer: h = 0.2446 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·200·0.06² = 0.36 J
Height
m·g = 0.15·9.81 = 1.472 N
h = ½kx²/(mg) = 0.36/1.472 = 0.2446 m
Answer
h = 0.2446 m
8.Work & energy
Answer: x = 34.69 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2.5 − 0.1·2) = 90.25 J
Maximum compression
½kx² = 90.25 → x = √(2·90.25/1500) = 0.3469 m = 34.69 cm
Answer
x = 34.69 cm
9.Momentum & collisions
Answer: ΔK = 273214 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1800·25/3500 = 12.86 m/s
Kinetic energy before and after
Kbefore = ½·1800·25² = 562500 J
Kafter = ½·3500·12.86² = 289286 J
Energy lost
ΔK = 562500 − 289286 = 273214 J
Answer
ΔK = 273214 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v = 1702 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.1·(1 − cos 30°) = 0.1474 m
Speed after impact
V = √(2·9.81·0.1474) = 1.7 m/s
Collision
v = (m + M)·V/m = 5.005·1.7/0.005 = 1702 m/s
Answer
v = 1702 m/s
11.Hydrostatic force
Answer: F = 9.81 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·1 = 9.81 kN
Answer
F = 9.81 kN
12.Hydrostatic force
Answer: F = 173.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.75·3.75 = 173.8 kN
Answer
F = 173.8 kN
13.Continuity & Bernoulli
Answer: p1 = 247.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(170000/1000 + 9.81·4)) = 20.46 m/s
Answer
v = 20.46 m/s
15.Ideal gas law
Answer: V = 54.74 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 320/28.01 = 11.42 mol
T = 15 + 273.15 = 288.1 K
Volume
V = nRT/P = 11.42·8.314·288.1/500 = 54.74 L
Answer
V = 54.74 L
16.Ideal gas law
Answer: V2 = 21.32 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 503.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(150/250)·(503.1/283.1) = 21.32 L
Answer
V2 = 21.32 L
17.Heat engines & refrigerators
Answer: ηmax = 61.48 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 475 + 273.15 = 748.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/748.1 = 61.48 %
Answer
ηmax = 61.48 %
18.Heat engines & refrigerators
Answer: Tm = 395 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 40 + 273.15 = 313.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1023 + 313.1)/2 = 668.1 K = 395 °C
Answer
Tm = 395 °C
19.Waves, sound & optics
Answer: L = 1.5 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 300/500 = 0.6 m
Length
L = nλ/2 = 5·0.6/2 = 1.5 m
Answer
L = 1.5 m
20.Waves, sound & optics
Answer: di = 60 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.