Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 300 km/h to take off and the usable runway is 1200 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 300 km/hs = 1200 m
a = m/s²
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 26 m/s² for 1 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 26 m/s²t1 = 1 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 6 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 40°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1 kgm2 = 4.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 18 m/s and must land 30 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 18 m/sR = 30 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 25 m/sθ = 15°h = 15 mg = 9.81 m/s²
x = m
7.Work & energyMedium
An 800 kg car drives up an 8° slope at a constant 90 km/h. Air resistance and rolling resistance together amount to 500 N. Find the power P the wheels must deliver, in kW.
A 1 kg cart is released from rest at a height of 7 m on a smooth track that leads into a vertical circular loop of radius 2 m. Find the speed v of the cart at the top of the loop.
m = 1 kgh = 7 mR = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 4 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 25 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 4 kgh = 25 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 1700 kg car runs into a parked 900 kg car. The wrecks lock together and skid 23 m before stopping. The coefficient of kinetic friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 2 mH = 2 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 170 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 25 mm while rising 7 m. At section 1 the pressure is 400 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at -20 °C by removing 3.5 kW of heat, and rejects heat to the surroundings at 28 °C. Find the rate Q̇H at which it rejects heat.
TL = -20 °CTH = 28 °CQ̇L = 3.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 60 kW of heat from a source at 750 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -15 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 750 °CT0 = 20 °CTL = -15 °CQ̇H = 60 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 25 cm in front of a thin converging lens with a focal length of 10 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 25 cmf = 10 cm
di = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 15 cm and lens 2 with f₂ = 10 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 15 cmf2 = 10 cms = 60 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: a = 2.894 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 300/3.6 = 83.33 m/s
Acceleration
a = v²/(2s) = 83.33²/(2·1200) = 2.894 m/s²
Answer
a = 2.894 m/s²
2.Kinematics
Answer: hmax = 47.45 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 26·1 = 26 m/s
h₁ = ½·26·1² = 13 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 26²/(2·9.81) = 34.45 m
hmax = 13 + 34.45 = 47.45 m
Answer
hmax = 47.45 m
3.Newton’s laws
Answer: a = 5.179 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·30/18² = 0.9083
Angle
2θ = 65.28° → θ = 32.64°
Answer
θ = 32.64°
The other solution is 90° − θ = 57.36°.
6.Projectile motion
Answer: x = 61.06 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 25·cos 15° = 24.15 m/s
vy = v0·sin θ = 25·sin 15° = 6.47 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 6.47·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (6.47 + √(41.87 + 294.3))/9.81 = 2.529 s
Horizontal distance
x = vx·t = 24.15·2.529 = 61.06 m
Answer
x = 61.06 m
7.Work & energy
Answer: P = 39.81 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 800·9.81 = 7848 N
mg·sin θ = 7848·sin 8° = 1092 N
F = 1092 + 500 = 1592 N
Power
v = 90/3.6 = 25 m/s
P = F·v = 1592·25 = 39806 W = 39.81 kW
Answer
P = 39.81 kW
8.Work & energy
Answer: v = 7.672 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(7 − 4) = 58.86 m²/s²
v = 7.672 m/s
Answer
v = 7.672 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 1774 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.25) = 2.215 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 4)·2.215/0.005 = 1774 m/s
Answer
v = 1774 m/s
10.Momentum & collisions
Answer: v1 = 22.97 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·4.5 = 154.5 kN
Answer
F = 154.5 kN
12.Hydrostatic force
Answer: ycp = 3.111 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3·4 = 103.6 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·2³/12 = 1.333 m⁴
ycp = yc + Ic/(yc·A) = 3 + 1.333/(3·4) = 3.111 m
Answer
ycp = 3.111 m
13.Continuity & Bernoulli
Answer: p2 = 168.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 28 + 273.15 = 301.1 K
TL = -20 + 273.15 = 253.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 3.5·301.1/253.1 = 4.164 kW
Answer
Q̇H = 4.164 kW
Power input: Ẇ = 0.6636 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 315.7 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 750 + 273.15 = 1023 K
T0 = 20 + 273.15 = 293.1 K
TL = -15 + 273.15 = 258.1 K
Engine work
η = 1 − 293.1/1023 = 0.7135
Ẇ = 0.7135·60 = 42.81 kW
Heat removed by the refrigerator
COPR = 258.1/(293.1 − 258.1) = 7.376
Q̇L = 7.376·42.81 = 315.7 kW
Answer
Q̇L = 315.7 kW
19.Waves, sound & optics
Answer: di = 16.67 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/10 − 1/25
di = 16.67 cm
Ray diagram
real, on the far side of the lens
Answer
di = 16.67 cm
20.Waves, sound & optics
Answer: di2 = 13.85 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.