Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3.75 m/s² along a runway. Find its speed v after 1800 m.
v₀ = 0a = 3.75 m/s²s = 1800 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 11 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5.5 kgm2 = 3.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 40 m/sθ = 20°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 60°h = 45 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 18 m along the slope.
θ = 40°μ = 0.35d = 18 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg cart is released from rest at a height of 12 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 2 kgh = 12 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 5 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 1.5 kgh = 5 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
At a crossing a 1800 kg car travelling east at 17 m/s collides with a 1400 kg car travelling north at 11 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1800 kgv1 = 17 m/s (E)m2 = 1400 kgv2 = 11 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows at 18 L/s through a horizontal pipe that narrows from 100 mm to 75 mm. The pressure in the narrow section is 190 kPa. Ignoring losses, find the pressure p1 in the wide section.
A closed water tank has compressed air above the water at a gauge pressure of 190 kPa. Water leaves through an opening with a diameter of 30 mm, 3.5 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 300 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 300 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 13 kW of heat to a heating system at 55 °C, taking heat from a source at -5 °C. Its actual COP is 40% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 55 °CTL = -5 °CηII = 40%Q̇H = 13 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1.5 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 1.5 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 450 nm passes through a single slit 0.05 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 450 nma = 0.05 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: v = 116.2 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3.75·1800) = 116.2 m/s
Answer
v = 116.2 m/s
(418.3 km/h)
2.Kinematics
Answer: t = 4.018 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 11·t − ½·9.81·t²
4.905·t² − 11·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (11 + √(11² + 2·9.81·35))/9.81 = 4.018 s
Answer
t = 4.018 s
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 20° = 37.59 m/s
vy = v0·sin θ = 40·sin 20° = 13.68 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.68/9.81 = 2.789 s
Answer
t = 2.789 s
6.Projectile motion
Answer: x = 89.34 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 60° = 14 m/s
vy = v0·sin θ = 28·sin 60° = 24.25 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 24.25·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (24.25 + √(588 + 882.9))/9.81 = 6.381 s
Horizontal distance
x = vx·t = 14·6.381 = 89.34 m
Answer
x = 89.34 m
7.Work & energy
Answer: v = 11.5 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·18·(0.6428 − 0.35·0.766)) = 11.5 m/s
Answer
v = 11.5 m/s
8.Work & energy
Answer: N = 19.62 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(12 − 8) = 78.48 m²/s²
Forces at the top
m·g = 2·9.81 = 19.62 N
N = mv²/R − mg = 2·78.48/4 − 19.62 = 19.62 N
Answer
N = 19.62 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 298.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.05) = 0.9905 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 1.5)·0.9905/0.005 = 298.1 m/s
Answer
v = 298.1 m/s
10.Momentum & collisions
Answer: v′ = 10.71 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(400/700)·(383.1/293.1) = 14.94 L
Answer
V2 = 14.94 L
17.Heat engines & refrigerators
Answer: ηmax = 51.47 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/573.1 = 51.47 %
Answer
ηmax = 51.47 %
18.Heat engines & refrigerators
Answer: Ẇ = 5.942 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 55 + 273.15 = 328.1 K
TL = -5 + 273.15 = 268.1 K
Carnot and actual COP
COPmax = 328.1/(328.1 − 268.1) = 5.469
COP = 0.4·5.469 = 2.188
Power input
Ẇ = Q̇H/COP = 13/2.188 = 5.942 kW
Answer
Ẇ = 5.942 kW
19.Waves, sound & optics
Answer: f5 = 285.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1.5/5 = 1.2 m
Frequency
f = v/λ = 343/1.2 = 285.8 Hz
Answer
f5 = 285.8 Hz
20.Waves, sound & optics
Answer: θ2 = 1.031 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …