Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 200 km/h to take off and the usable runway is 2200 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 200 km/hs = 2200 m
a = m/s²
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 14 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 10 mv0B = 14 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 160 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 160 Nθ = 35°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3 kg block on a ramp at 25° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 6.5 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3 kgm2 = 6.5 kgθ = 25°μ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 20 m/s and 45° above the horizontal towards a wall 29 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 20 m/sθ = 45°x = 29 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is thrown from ground level at 29 m/s and 65° above the horizontal. It lands on the flat roof of a building 4 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 29 m/sθ = 65°hroof = 4 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 5 m along the slope.
θ = 25°μ = 0.35d = 5 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 1 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.2) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 1 kgh = 2 mL = 4 mμ = 0.2k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2.5 kgm2 = 5 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 15 g bullet is fired horizontally into a 3.5 kg block hanging from light strings 1.3 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 3.5 kgL = 1.3 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 1 mb = 3 mρ = 1025 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 5 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 3 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A reversible refrigerator keeps a cold room at 2 °C by removing 7 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = 2 °CTH = 25 °CQ̇L = 7 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat engine takes in 1800 kJ of heat from a reservoir at 750 °C, produces 648 kJ of work and rejects the rest to a reservoir at 15 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 750 °CTL = 15 °CQH = 1800 kJW = 648 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object 1.5 cm tall stands 18 cm in front of a thin converging lens with a focal length of 8 cm. Find the image height hi (negative for an inverted image).
ho = 1.5 cmdo = 18 cmf = 8 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls on two slits 0.25 mm apart. The screen is 1.5 m away. Find the distance y1 from the central bright fringe to bright fringe number 1.
λ = 532 nmd = 0.25 mmL = 1.5 mm = 1
y1 = mm
3Solutions
1.Kinematics
Answer: a = 0.7015 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 200/3.6 = 55.56 m/s
Acceleration
a = v²/(2s) = 55.56²/(2·2200) = 0.7015 m/s²
Answer
a = 0.7015 m/s²
2.Kinematics
Answer: y = 7.497 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 14·t − ½g·t² → t = 10/14 = 0.7143 s
Meeting height
y = 14·0.7143 − ½·9.81·0.7143² = 7.497 m
Answer
y = 7.497 m
3.Newton’s laws
Answer: a = 5.248 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 160·sin 35° = 104.4 N
Horizontal forces
m·a = F·cos θ − μ·N = 131.1 − 26.11
a = 105/20 = 5.248 m/s²
Answer
a = 5.248 m/s²
4.Newton’s laws
Answer: T = 28.65 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 63.77 N
m₁·g·sin θ = 12.44 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (63.77 − 12.44 − 0)/9.5 = 5.403 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 6.5·(9.81 − 5.403) = 28.65 N
Answer
T = 28.65 N
5.Projectile motion
Answer: y = 8.374 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 20·cos 45° = 14.14 m/s
t = x/vx = 29/14.14 = 2.051 s
Height at that time
y = 14.14·2.051 − ½·9.81·2.051² = 8.374 m
Answer
y = 8.374 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 63.75 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 12.26 m/s, vy = 26.28 m/s
Time to land on the roof
Larger root: the ball is descending.
4 = 26.28·t − 4.905·t²
t = (26.28 + √(26.28² − 2·9.81·4))/9.81 = 5.202 s
Horizontal distance
x = vx·t = 12.26·5.202 = 63.75 m
Answer
x = 63.75 m
7.Work & energy
Answer: v = 3.216 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·5·(0.4226 − 0.35·0.9063)) = 3.216 m/s
Answer
v = 3.216 m/s
8.Work & energy
Answer: v = 4.852 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(2 − 0.2·4) = 11.77 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·1.2) = 4.852 m/s
Answer
v = 4.852 m/s
9.Momentum & collisions
Answer: v′1 = −3.667 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 5)/(2.5 + 5)·11 = −3.667 m/s
v′2 = 2·2.5/(2.5 + 5)·11 = 7.333 m/s
Answer
v′1 = −3.667 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 433.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.3·(1 − cos 30°) = 0.1742 m
Speed after impact
V = √(2·9.81·0.1742) = 1.849 m/s
Collision
v = (m + M)·V/m = 3.515·1.849/0.015 = 433.2 m/s
Answer
v = 433.2 m/s
11.Hydrostatic force
Answer: F = 104.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.25·2.5 = 104.2 kN
Answer
F = 104.2 kN
12.Hydrostatic force
Answer: F = 135.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4.5·3 = 135.7 kN
Answer
F = 135.7 kN
13.Continuity & Bernoulli
Answer: Q = 9.584 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: V = 74.54 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 350/16.04 = 21.82 mol
T = 35 + 273.15 = 308.1 K
Volume
V = nRT/P = 21.82·8.314·308.1/750 = 74.54 L
Answer
V = 74.54 L
16.Ideal gas law
Answer: V2 = 6.903 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(200/100)·(523.1/303.1) = 6.903 L
Answer
V2 = 6.903 L
17.Heat engines & refrigerators
Answer: Q̇H = 7.585 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = 2 + 273.15 = 275.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 7·298.1/275.1 = 7.585 kW
Answer
Q̇H = 7.585 kW
Power input: Ẇ = 0.5851 kW.
18.Heat engines & refrigerators
Answer: Sgen = 2.239 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1800 − 648 = 1152 kJ
Absolute temperatures
TH = 750 + 273.15 = 1023 K
TL = 15 + 273.15 = 288.1 K
Entropy changes of the reservoirs
ΔSH = −1800/1023 = −1.759 kJ/K
ΔSL = 1152/288.1 = 3.998 kJ/K
Sgen = 3.998 − 1.759 = 2.239 kJ/K
Answer
Sgen = 2.239 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: hi = −1.2 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/8 − 1/18
di = 14.4 cm
Magnification and height
m = −14.4/18 = −0.8
hi = −0.8·1.5 = −1.2 cm
Answer
hi = −1.2 cm
20.Waves, sound & optics
Answer: y1 = 3.192 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …