Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 45 km/ha = −7.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 7 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 7 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 17 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 17 kgθ = 20°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9 kg block on a ramp at 20° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 9.5 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 9 kgm2 = 9.5 kgθ = 20°μ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 22 m/sθ = 25°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 29 m/sθ = 50°h = 5 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 0.5 kg ball hangs on a light string of length 1 m. It is pulled aside until the string makes 45° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 0.5 kgL = 1 mθ = 45°g = 9.81 m/s²
T = N
8.Work & energyHard
A 5 kg block starts from rest at the bottom of a 30° slope and is pulled up the slope by a constant force of 45 N parallel to the slope. The coefficient of kinetic friction is 0.15. Find the speed v of the block after it has moved 6 m up the slope.
A 3.5 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 2.5 kgv1 = 3 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.45 kg ball hits a wall at 27 m/s and bounces straight back at 9 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.45 kgvin = 27 m/svout = 9 m/sΔt = 50 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 150 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 150 mm, throat 75 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 340 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 20 °C. Find the highest possible thermal efficiency ηmax.
TH = 425 °CTL = 20 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -10 °C outside, delivering 15 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = -10 °CQ̇H = 15 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light travels in glycerol (n = 1.47) towards a flat boundary with air (n = 1.00). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.47n2 = 1.00
θc = °
20.Waves, sound & opticsHard
Light of wavelength 550 nm passes through a single slit 0.08 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 550 nma = 0.08 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: t = 1.667 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 12.5/7.5 = 1.667 s
Answer
t = 1.667 s
2.Kinematics
Answer: t = 2.31 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 7·t − ½·9.81·t²
4.905·t² − 7·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (7 + √(7² + 2·9.81·10))/9.81 = 2.31 s
Answer
t = 2.31 s
3.Newton’s laws
Answer: a = 1.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 93.2 N
m₁·g·sin θ = 30.2 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (93.2 − 30.2 − 0)/18.5 = 3.405 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 9.5·(9.81 − 3.405) = 60.84 N
Answer
T = 60.84 N
5.Projectile motion
Answer: t = 1.896 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 22·cos 25° = 19.94 m/s
vy = v0·sin θ = 22·sin 25° = 9.298 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·9.298/9.81 = 1.896 s
Answer
t = 1.896 s
6.Projectile motion
Answer: t = 4.744 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 29·cos 50° = 18.64 m/s
vy = v0·sin θ = 29·sin 50° = 22.22 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 22.22·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (22.22 + √(493.5 + 98.1))/9.81 = 4.744 s
Answer
t = 4.744 s
7.Work & energy
Answer: T = 7.778 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1·(1 − cos 45°) = 5.747 m²/s²
Forces at the bottom
m·g = 0.5·9.81 = 4.905 N
T = mg + mv²/L = 4.905 + 0.5·5.747/1 = 7.778 N
Answer
T = 7.778 N
Check: T = mg(3 − 2cos θ) = 7.778 N.
8.Work & energy
Answer: v = 5.818 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 5·9.81 = 49.05 N
mg·sin θ = 24.52 N
μ·mg·cos θ = 6.372 N
Work–energy
½mv² = (45 − 30.9)·6 = 84.62 J
v = √(2·84.62/5) = 5.818 m/s
Answer
v = 5.818 m/s
9.Momentum & collisions
Answer: v′2 = 3.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 2.5)/(3.5 + 2.5)·3 = 0.5 m/s
v′2 = 2·3.5/(3.5 + 2.5)·3 = 3.5 m/s
Answer
v′2 = 3.5 m/s
10.Momentum & collisions
Answer: J = 16.2 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.45·(9 + 27) = 16.2 N·s
Answer
J = 16.2 N·s
11.Hydrostatic force
Answer: F = 14.71 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·1 = 14.71 kN
Answer
F = 14.71 kN
12.Hydrostatic force
Answer: F = 161.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.75·5 = 161.9 kN
Answer
F = 161.9 kN
13.Continuity & Bernoulli
Answer: p2 = 149.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.34 = 42026 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(150/450)·(443.1/283.1) = 1.043 L
Answer
V2 = 1.043 L
17.Heat engines & refrigerators
Answer: ηmax = 58.01 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/698.1 = 58.01 %
Answer
ηmax = 58.01 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.626 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 15/9.223 = 1.626 kW
Answer
Ẇmin = 1.626 kW
19.Waves, sound & optics
Answer: θc = 42.86 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.00/1.47 = 0.6803
Critical angle
θc = arcsin(0.6803) = 42.86°
Answer
θc = 42.86°
20.Waves, sound & optics
Answer: θ2 = 0.7878 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …